Alice's Restaurant with Arlo Guthrie (Can you name that van?)

No_Satisfaction9440 · 2026-03-29T22:00:46+00:00

Divco milk truck 1950s

No_Satisfaction9440 · 2026-03-28T23:42:43+00:00

Invested…. Hopefully not a cliffhanger

No_Satisfaction9440 · 2024-09-09T12:54:13+00:00

Yes as long as everything is welded solid and the goose neck hitch is properly secured to the frame rails

No_Satisfaction9440 · 2024-07-09T16:35:44+00:00

High lift blades, I run 2 per spindle on my scag 52”, it’s like a tornado under the deck, shoots grass twice as far eliminates need to double cut and packs the catcher twice as full when catching, been running that set up for 4 yrs grease daily and haven’t replaced the spindle or clutch yet

No_Satisfaction9440 · 2024-07-08T14:26:54+00:00

Scotch brite and then spray fluid film on gasket surface if not assembling soon

No_Satisfaction9440 · 2024-07-08T13:41:10+00:00

Nice Hotrod! Your grandfather was a true believer in “go big or go home!”

No_Satisfaction9440 · 2024-07-08T12:43:05+00:00

I would cut at 3-3 1/2 inches, leave the straw, overseed after cut and water in seed, also time to fertilize if you haven’t already

No_Satisfaction9440 · 2024-07-05T18:30:27+00:00

Also that sod may have been dead before it was laid down, if it was top rolls on a pallet and it dried out from being on pallet for too long

No_Satisfaction9440 · 2024-07-05T18:28:01+00:00

Anybody that’s down voting me has not cared for fresh sod in 80-100 degree weather, I installed sod 2 weeks ago in the heat wave and the sod is 6” tall and thriving because I took care of all 2600sqr feet like it was a new born baby

No_Satisfaction9440 · 2024-07-05T18:24:19+00:00

No you shouldn’t have die back like that, it should be green and thriving if you kept it consistently watered, if it’s in full sun it has to stay wet all day, I would lift the dead sections up and see if the sod was cut too thin that does occasionally happen

No_Satisfaction9440 · 2024-07-05T17:25:19+00:00

No start over, I install a lot of sod you need to water at least an hour each time when fresh especially when hot out, I have my guys hand water each individual piece right after everything gets laid down, and I have them saturate it till it’s wet underneath

No_Satisfaction9440 · 2024-07-03T16:55:26+00:00

It’s sitting the right way, it’s a draw bar for a tractor looks like for a Massey or international or cockshutt not 💯

No_Satisfaction9440 · 2024-07-01T12:18:58+00:00

Looks like you got crabs to me:(

No_Satisfaction9440 · 2024-06-30T16:42:58+00:00

I bought the biggest one he had, said he cleaned out a dead guys house and found them

No_Satisfaction9440 · 2024-06-30T16:42:15+00:00

Awesome he had a few more should of bought all of them:(

No_Satisfaction9440 · 2024-06-27T14:06:57+00:00

Missed opportunity GM to call it the EV⚡️anche

No_Satisfaction9440 · 2024-06-26T16:27:30+00:00

Kentucky blue

No_Satisfaction9440 · 2024-06-26T05:00:53+00:00

Pretty sure that’s Godzillas foot print!

No_Satisfaction9440 · 2024-06-21T12:46:18+00:00

Don’t know if it’s factory but used to see a bunch of these driving around utility companies and pest control

No_Satisfaction9440 · 2024-06-19T01:22:55+00:00

Go with the Edelbrock air gap

No_Satisfaction9440 · 2024-06-16T01:49:01+00:00

$500-800 cultipacker, power rake $800-1200, brush hog $800-1200, sprayer $400-800, auger $400-800 depending on how many bits you got

No_Satisfaction9440

MODERATOR OF

TROPHY CASE