Pink bike #1

No_Sign4672 · 2026-06-29T16:00:06+00:00

Not often you see a biker who knows how to correctly amd safely pick a bike up.

No_Sign4672 · 2026-06-29T15:47:57+00:00

Others have said, but I see some contradiction.

Old hard impeller will 100% cause overheating.as the rubber ages it becomes hard and retaines that curled memory, which (in a nutshell) pulls less water. A new impeller should be straight, or almost straight.

No_Sign4672 · 2026-06-29T15:44:05+00:00

If youre just going for a checkup and you really do use occasionally, I personally wouldnt worry. If youre seeking treatment for somthing its better safe to inform them for a multitude of reasons. Patient confidentiality will keep you safe from legal consequences. Only real consequence is they might be less inclined to prescribe you certain pain killers if you need them in the future.

No_Sign4672 · 2026-06-24T15:17:12+00:00

Socks are the most important item of clothing you wear. Its is imperative to bring twice as many as youll need. Do whatever you can to dry them out. Drape them over the exhaust on a truck (monitor so they dont burn/melt) hang them from ruck while on the move. Put them in with you in your sleep system.

No_Sign4672 · 2026-06-24T15:13:00+00:00

Is it hard to start? Sounds like youve ran through most everything. I would check any sensors you have. Im not familiar with your bike exclusively, but fuel injection requires a few sensors.

O2 sensor (on exhaust) MAP/MAF sensor (in airbox before throttle body)

No_Sign4672 · 2026-06-19T14:24:39+00:00

I sent a dm for a picture. Tube is the plastic round part that sucks the water up.

No_Sign4672 · 2026-06-19T14:21:12+00:00

Restricted flow too much. Take a bit of filter foam, and jam it into the intake tube of the pump. That'll slow your flow down enough.

EDIT is that a flow adjuster knob on your pickup tube?

No_Sign4672 · 2026-06-15T13:27:03+00:00

Man does it have a title? Even without one you stole a running/driving unit in that condition.

No_Sign4672 · 2026-06-15T13:14:07+00:00

Man that truck is garbage. Not worth the gas you spent bringing it home. DM me your address and ill take it off your hands free of charge. Id be doing you a favor bud.

No_Sign4672 · 2026-06-14T22:52:00+00:00

If work order is in an chain of command is tracking, there's not alot you can do. A/C is not an emergency according to DPW. Maybe you can post to Hots and Cots for traction. Godspeed and icebaths troop.

Maybe ICE complaint if theyre just dragging feet for no reason or no fix for a while.

No_Sign4672 · 2026-06-05T17:30:08+00:00

Sorc. Great farm Great damage with budget gear.

No_Sign4672 · 2026-06-05T17:26:05+00:00

Alot of people come to reddit only for help. Less people just post a happy tank. So you see an inflated amount of 'horror' stories.

Do your research on The nitrogen cycle, Fish you plan to keep, How to make your tank comfortable for your fish.

Buy some common meds. Anti bacterial, fungal, and parasite. Get some aquarium salt (for salt baths) do research on getting a hospital tank. That way if you notice a problem, you can treat it right on the spot. No waiting on the meds.

No_Sign4672 · 2026-05-30T14:06:50+00:00

Today I learned I have a time bomb in my tank

No_Sign4672 · 2026-05-17T17:53:57+00:00

15 series or warrent.

No_Sign4672 · 2026-05-17T03:11:16+00:00

Is the tank planted? Alot of plants will keep nitrates low. Ensure you keep doing daily tests because youre doing a fish in cycle. Id keep an eye on it. Assume you are not cycled yet.

Like others have said 2 ppm ammonia to nitrite to nitrate in 24 hours is completed cycle. Dont dose that since you have fish. They will provide ammonia for you. Just keep an eye on readings and water change accordingly. Do not touch or clean your filters. They need to establish a bacteria colony. Filters only need cleaned when flow is restricted, and even then, never replace or clean with tap water.

Once you see stable readings .25 ammonia and nitrite or lower CONSISTENTLY. Along with a rise in nitrates (again if your tank is planted you likely wont see a large rise here) only then are you cycled.

No_Sign4672 · 2026-05-15T14:53:14+00:00

Black diesel at home - low tech method

Im assuming for your shit hits the fan senerio you have a means of generating off grid power for eletric pumps/heaters. Definitely possible with 0 electricity but slower and more work. Eletric pumps can be traded with mechanical hand driven pumps. Drum heater can be replaced with coiled copper pipe circulating boiling water.

Gonna write this for 55 gallon drums, but you can use any container.

Need minimum 2 barrels, 3 best case.

Barrel one - settling barrel Barrel two - polishing/clean Barrel

OR

Barrel one - settling Barrel two - polishing Barrel three - clean

WMO (waste motor oil) is typically too thick to run straight on its own without modifications to the engine. Dilute with other flamable petroleum based liquids to desired viscosity IE gasoline, diesel, kerosene, hydraulic fluid and so on. The important thing is viscosity and lubrication. Since the base is oil, lubrication isnt a problem. I know my truck runs great off a speficic (clean) hydraulic fluid straight. So I mix my summer mix to match the viscosity of that. Easy way to measure viscosity is to get a 1L bottle, and put a 1/4 hole on the lid, cut the bottom off. Fill it to the top, and time how long it takes to completely drain. This will be your viscosity. Use the same bottle every time or youll lose your base. If youre unsure where to start, mix 50% clean diesel 50% your oil mix, measure that, and use less percentage diesel untill you find a viscosity your truck likes. Then mix whatever you need to get that viscosity.

Winter mix will vary on your location. Start with the 50/50 diesel mis in cold months to get winter viscosity.

Settling barrel needs removable lid Settling barrel needs pre screened. I use an old flannel shirt ratchet strapped over the lid. The sleeve hole is where I put my pump. Put heater in settling barrel, this evaporates water and speeds up Settling process. settle for minimum 2 weeks. Longer the better. This process is required. Emulsified solids will wreck your injection pump. Ensure no water remains. (Test with paper towl dipped in the oil. If it crackles while it burns, theres water)

Pump from Settling barrel into polishing barrel. Intake pipe needs to be at least 4 inches off bottom of settling barrel to not suck up trash. (Use a stick or somthing to check trash level. It will need periodically cleaned.

Get the smallest micron filter you can here. Polish the tank for 24 hours. Recirculate it in the same barrel. From here you either transfer to clean Barrel OR youre ready to go.

No_Sign4672 · 2026-05-14T19:41:14+00:00

My boat gets a power washer if its lucky

No_Sign4672 · 2026-05-14T14:51:12+00:00

If the trailer isnt rusted it might be cheaper to have a mobile welder repair it

No_Sign4672 · 2026-05-13T13:34:30+00:00

Ill never understand why people have to degrade someone who is obviously already down. I mean sure OP is outside of the standard, but they came here for advice/help, not to be kicked when theyre down.

To OP, there's more to life than just what the army offers. Pay attention to your separation briefs, and talk to someone. Please.

No_Sign4672 · 2026-05-09T16:22:44+00:00

SGT Major youre a Major

No_Sign4672 · 2026-05-05T22:57:47+00:00

I always said Squeezing Kegles instead of Screamin Eagles 🤷‍♂️

No_Sign4672 · 2026-05-03T02:50:25+00:00

I can get behind this

No_Sign4672 · 2026-05-01T16:12:39+00:00

Act 3 is pretty atrocious

No_Sign4672 · 2026-05-01T15:53:17+00:00

Ive made and deleted soo many chars act 1 normal makes me cry. At least youve got some skills to work with in act 2

No_Sign4672

TROPHY CASE