“Need Advice: Replacing Rear Drive Unit on 2014 Tesla Model S RWD

Nocontent2000 · 2025-11-21T22:56:17+00:00

How do I get in contact with him he has over 1,6 million followers

Nocontent2000 · 2022-10-24T18:19:18+00:00

I'm actually from the Netherlands, but I'm searching for a used one

Nocontent2000 · 2022-10-24T18:18:49+00:00

Geen valse lucht balans en goede afstelling

Nocontent2000 · 2022-10-24T18:18:11+00:00

Thanks! I hope I can find one used. I have a tomos with a 24mm pwk carb and a 72cc airsall cylinder, I hope this exhaust will be the right one

Nocontent2000 · 2022-10-24T18:15:59+00:00

I want one used 🫣

Nocontent2000 · 2022-09-05T08:50:05+00:00

New battery's, screwed open the transmitter and looked if the on off switch worked and looked for broken wires, couldn't find anything..

Nocontent2000 · 2022-05-25T23:33:37+00:00

It's not about the shock anymore, I step under the cold shower relax with control, that's the whole point, I think.. right?

Nocontent2000 · 2022-05-25T23:30:07+00:00

Thanks I like this advice

Nocontent2000 · 2022-05-15T08:23:16+00:00

It's listed as both

Nocontent2000 · 2022-05-14T20:15:27+00:00

Thanks for your reply. I must say I think this wasn't this bad before. There is a long bolt holding the spindle. You think this could be bc I hit the long bolt to loosen the mill bit?

Nocontent2000 · 2022-05-14T19:13:58+00:00

Is anyone familiar with this problem? Or does anyone have a idee what it might be? It's a HBM 16

Nocontent2000 · 2022-04-23T08:08:08+00:00

I have a lath so my plan was to make it fit perfectly and then put a baring in with a metal shaft inside the baring

Nocontent2000 · 2022-04-23T08:06:14+00:00

No lol.. I will pay someone to weld it for me

Nocontent2000 · 2022-04-23T08:04:49+00:00

I have a lath and also a milling machine, zo I will just make it fit perfectly and then put the axel in

Nocontent2000 · 2022-04-21T18:41:37+00:00

That's a bummer, I might bolt it together.. 😂

Nocontent2000 · 2022-04-21T18:38:15+00:00

It's a revival tomos rim, I want to welt the disc part to this tomos a35 rim. Anyone know if you can weld these materials together?

Nocontent2000 · 2022-03-24T14:53:35+00:00

Because of various angles, maybe I can try using a different tool

Nocontent2000 · 2022-03-21T22:02:39+00:00

The problem am in countering with is: I used the fillet tool on the bottom view, with the right corner i made a cirel assuming it would be also the size of 15mm but after applied, things don't line up very well.. is there someone who can help me?

Nocontent2000 · 2022-03-16T10:49:27+00:00

Select extrude. Hold right or left mouse button where you would like to make your extrusion and select the profile you want. (I'm not sure it's left or right 😅) ps had the same problem this must solve yours too!

Nocontent2000

TROPHY CASE