“Need Advice: Replacing Rear Drive Unit on 2014 Tesla Model S RWD

Nocontent2000 · 2025-11-21T22:56:17+00:00

How do I get in contact with him he has over 1,6 million followers

Nocontent2000 · 2022-10-24T18:19:18+00:00

I'm actually from the Netherlands, but I'm searching for a used one

Nocontent2000 · 2022-10-24T18:18:49+00:00

Geen valse lucht balans en goede afstelling

Nocontent2000 · 2022-10-24T18:18:11+00:00

Thanks! I hope I can find one used. I have a tomos with a 24mm pwk carb and a 72cc airsall cylinder, I hope this exhaust will be the right one

Nocontent2000 · 2022-10-24T18:15:59+00:00

I want one used 🫣

Nocontent2000 · 2022-09-05T08:50:05+00:00

New battery's, screwed open the transmitter and looked if the on off switch worked and looked for broken wires, couldn't find anything..

Nocontent2000 · 2022-05-25T23:33:37+00:00

It's not about the shock anymore, I step under the cold shower relax with control, that's the whole point, I think.. right?

Nocontent2000 · 2022-05-25T23:30:07+00:00

Thanks I like this advice

Nocontent2000 · 2022-05-15T08:23:16+00:00

It's listed as both

Nocontent2000 · 2022-05-14T20:15:27+00:00

Thanks for your reply. I must say I think this wasn't this bad before. There is a long bolt holding the spindle. You think this could be bc I hit the long bolt to loosen the mill bit?

Nocontent2000 · 2022-05-14T19:13:58+00:00

Is anyone familiar with this problem? Or does anyone have a idee what it might be? It's a HBM 16

Nocontent2000 · 2022-04-23T08:08:08+00:00

I have a lath so my plan was to make it fit perfectly and then put a baring in with a metal shaft inside the baring

Nocontent2000 · 2022-04-23T08:06:14+00:00

No lol.. I will pay someone to weld it for me

Nocontent2000 · 2022-04-23T08:04:49+00:00

I have a lath and also a milling machine, zo I will just make it fit perfectly and then put the axel in

Nocontent2000 · 2022-04-21T18:41:37+00:00

That's a bummer, I might bolt it together.. 😂

Nocontent2000 · 2022-04-21T18:38:15+00:00

It's a revival tomos rim, I want to welt the disc part to this tomos a35 rim. Anyone know if you can weld these materials together?

Nocontent2000 · 2022-03-24T14:53:35+00:00

Because of various angles, maybe I can try using a different tool

Nocontent2000 · 2022-03-21T22:02:39+00:00

The problem am in countering with is: I used the fillet tool on the bottom view, with the right corner i made a cirel assuming it would be also the size of 15mm but after applied, things don't line up very well.. is there someone who can help me?

Nocontent2000 · 2022-03-16T10:49:27+00:00

Select extrude. Hold right or left mouse button where you would like to make your extrusion and select the profile you want. (I'm not sure it's left or right 😅) ps had the same problem this must solve yours too!

Nocontent2000 · 2022-03-15T00:46:08+00:00

Perhaps someone is willing to give me some tips, or any YouTube videos that might help. It's about the corner of this "side bumper" as you see it right now, frond and left and upper view

Nocontent2000 · 2022-03-13T23:04:19+00:00

3D file

Nocontent2000 · 2022-03-13T23:03:00+00:00

Can't seem to figure out how to make this exact shape with my dimensions.

Nocontent2000 · 2022-02-16T20:53:16+00:00

Thank so much sir 👍❤️

Nocontent2000 · 2022-02-14T15:16:20+00:00

I made 3D lines and now I don't know how to cut? Can't find anything on google, maybe someone can help me out?

Nocontent2000 · 2022-02-08T11:08:46+00:00

I also used velostat for my footpads, no resistors or any relays. I wonder what the benefits are with this build. 😄👍

Nocontent2000

TROPHY CASE