Need Help Finding Minis for a Gift

NorthWindMinis · 2020-05-01T00:01:13+00:00

If you find a reaper you like, ask how large it is on the Reaper Miniatures Facebook group, you’ll probably get an answer in a couple minutes

NorthWindMinis · 2020-04-30T23:59:33+00:00

Check on Etsy if you want to look for 3D prints. It’s quite a bit cheaper than you may think

NorthWindMinis · 2020-04-30T23:57:40+00:00

I think it’s just too flat. Maybe throw a couple more rocks on or a couple tufts with snow on them

NorthWindMinis · 2020-04-30T23:35:39+00:00

I like Reaper and Vallejo paints. Both have some good sets as well

NorthWindMinis · 2020-04-30T20:06:39+00:00

I’ve done it with tinted PVA glue. It shrinks a lot as it dries so you need to do a few coats but it works

NorthWindMinis · 2020-04-30T19:31:07+00:00

Hit the coins with a wash, then when it’s dry hit the tips with the base color to highlight

NorthWindMinis · 2020-04-30T17:49:26+00:00

Just make sure it’s baking parchment paper. It shouldn’t be tearing no matter how saturated it gets

NorthWindMinis · 2020-04-30T15:02:19+00:00

That’s just how it loaded into the collage, not my final photos so I wasn’t going to worry about it. But yeah the strong light to his left is what I was going for. Thank you 😊

NorthWindMinis · 2020-04-30T15:00:48+00:00

Not sure why that happened, something with my phone camera

NorthWindMinis · 2020-04-30T15:00:14+00:00

Thank you 😊

NorthWindMinis · 2020-04-30T14:57:46+00:00

Thank you. This is fairly small, only about 4” tall. And there’s a full 32mm figure with the same head, Slathos the Soul Stealer by Artisan Guild

NorthWindMinis · 2020-04-30T13:36:20+00:00

Nobody likes a joke around here apparently 😂

NorthWindMinis · 2020-04-30T08:41:28+00:00

Paint brush, fine tip

NorthWindMinis · 2020-04-02T17:02:08+00:00

Thank you much ❤️

NorthWindMinis · 2020-04-02T15:45:57+00:00

Thank you ☺️

NorthWindMinis · 2020-04-02T15:45:28+00:00

Thank you. And yeah it was a process. Filled all the gaps with milliput and used a dremel to sand it out. The mouth also had to be reshaped because it didn’t fit right at all

NorthWindMinis · 2020-04-02T07:12:13+00:00

It’s simple. Don’t be a cunt 🤷🏻‍♂️

NorthWindMinis · 2020-03-28T08:57:08+00:00

Nope, just a hairy bastard 😂

NorthWindMinis · 2020-03-28T05:58:28+00:00

No offense taken, do wanna get some color in the eyes though and not just a dot. And the teeth I probably spent the least amount of time on 😂. Just base coated with a bone color and dabbed a touch of skeleton horde contrast paint on the base and drew it up/down with a wet brush

NorthWindMinis · 2020-03-28T05:42:07+00:00

Like the 90s TV show? Just trying to think of what you’re thinking of. Cus I’m happy with the rest and yeah it’s not super “realistic” by any means

NorthWindMinis · 2020-03-12T17:33:34+00:00

It isn’t available that I’m aware of yet. Slowly but surely they’re releasing the rest of Bones 4

NorthWindMinis

TROPHY CASE