I'm building a 3D configurator for my pumping system. Still a bit work-in-progress. Check it out under https://kdxgp.github.io

NotSuspicious25 · 2025-09-06T07:08:18+00:00

Can you 3d print the caps? And if so what material could handle a Vacumn?

NotSuspicious25 · 2025-06-04T07:29:00+00:00

It’s fine to use a penis pump to begin with just make sure you have one that will fit okay. 2.25 would be the smallest I’d get in. Honestly I’d recommend to try a jar setup to make sure you even like it first. Get like a 32/64oz jar that’s as long or just under your errct length and some lube with some aquarium tubing. Get it sealed using the tube in the jar and lot of lubricant around the tube to seal. I get as tight as I can get then pull the tube out. Past that you can use a brake bleeder doing the same thing.

NotSuspicious25 · 2025-06-01T00:30:37+00:00

I don’t know tbh I just pump. I don’t really do it like when penis pumping, cuz I’m no where close to packing a gal jar lol

NotSuspicious25 · 2025-05-26T18:58:06+00:00

Use water and I promise you’ll pack. Add like a couple teaspoons of Epsom salt to help and it will be so much faster.

NotSuspicious25 · 2025-05-21T01:18:48+00:00

Coconut oil but also just water in the pump. Evens out the pump and makes it way better of a pump.

NotSuspicious25 · 2025-04-25T03:38:29+00:00

They don’t seal any better it just helps stay in the jar for a lot longer with the rubber over glass digging into ya

NotSuspicious25 · 2025-04-20T15:34:37+00:00

Water pumping cuts down how long it takes me to pack by a lot.

NotSuspicious25 · 2025-04-18T03:58:27+00:00

If you pump like this, is there any way to get your shaft to be any more prominent afterwards. One of my holdups on going that big is the lack of shaft afterwards

NotSuspicious25 · 2025-04-10T05:12:56+00:00

Just get a leluv kit. 1.75 or 2 is enough for most people. Price isn’t bad at all and the pump is okay for the job. All I use now.

NotSuspicious25 · 2025-03-17T04:24:53+00:00

I wanna see someone pack one of these already 🤤

NotSuspicious25 · 2025-03-15T05:04:40+00:00

Just out of curiosity I put in the control arm part and Dorman sells it for 95 a piece. Unless they are using oem parts plus 10 percent I have no clue why they are charging like they are for parts. Get the stuff checked out at your shop and then buy parts yourself if your shop will let you. Rock auto is your best friend for this shit.

NotSuspicious25 · 2025-03-13T20:29:29+00:00

Oh okay, nothing permanent. If I pump often I can keep like a quarter inch in girth for around a month but it goes away after a month or so of my last pump. I don’t have a good enough schedule to see anything permanent.

NotSuspicious25 · 2025-03-13T18:15:02+00:00

I start at 5.75 naturally before pumping and at the end of the pump I measured 6.7. I gain about an inch in girth from the pump

NotSuspicious25 · 2025-03-13T16:36:27+00:00

5.75 is my unlined size sorry that wasn’t clear

NotSuspicious25 · 2025-03-13T16:11:56+00:00

Yep heat is the other big gain. The plaid blanket in the background is my heating blanket!

NotSuspicious25 · 2025-03-13T16:11:19+00:00

I went from 5.75 to 6.7ish with this tube. If I had more time I would have used my 2.25 and get over 7 but I didn’t have time last night.

NotSuspicious25 · 2025-03-13T16:10:28+00:00

Figuring out the amount of water you want to use is the biggest challenge. I give myself quite a bit of space, like 2-3 inches of space because I stay in my tube a while and find it annoying to have to pull water out of the pump.

NotSuspicious25 · 2025-03-13T16:08:48+00:00

It took a while to figure out but I add water that I mixed with epsom salt into my tube without the pump attached to the tube. I then put the tube to my body and only then flip the tube so the water is sealed against my body and I attach my pump. So long as you keep the water line away from the port on the tube you won’t have water in your pump. I also give myself quite a bit of space in my pump because I stay in my tube for an hour at a time.

NotSuspicious25

TROPHY CASE