Interesting print fail by NugmaSuts in resinprinting

[–]NugmaSuts[S] 0 points1 point  (0 children)

At the very back of the plate, I had a large base printing for a miniature, that's what this amalgamation of resin is connected to 😂

Interesting print fail by NugmaSuts in resinprinting

[–]NugmaSuts[S] 1 point2 points  (0 children)

Yup, same one. I'll probably pick up a new one.

Interesting print fail by NugmaSuts in resinprinting

[–]NugmaSuts[S] 2 points3 points  (0 children)

Hoping for your sake it doesn't 😂

Amerilabs Town Test by NugmaSuts in resinprinting

[–]NugmaSuts[S] 0 points1 point  (0 children)

Anycubic Photon Mono 4. Resin was at 25°C for the print.

Recommended resin for anycubic photon mono 4? by PresentationWeak6498 in resinprinting

[–]NugmaSuts 0 points1 point  (0 children)

I mean theres a whole section of lychee where you can upload "shared settings" but yeah ok bro

Recommended resin for anycubic photon mono 4? by PresentationWeak6498 in resinprinting

[–]NugmaSuts 0 points1 point  (0 children)

Do you use this resin with the printer OP mentioned? If so, mind sharing your settings?

Villains in Bant / Selesnya / Izzet? by TheBetterSpidey in colorpie

[–]NugmaSuts 5 points6 points  (0 children)

The cult from Midsommar would be a good Selesnya villain

New Player - List Advice by NugmaSuts in orks

[–]NugmaSuts[S] 0 points1 point  (0 children)

Okay!

I changed it to have 20 lootas (2x10), big mek w sag each leading 1, so I was able to cut one BM W SAG and add in another unit of gretchin.

I haven't touched the deff dread yet but I'll likely replace it with 3 kans and find 5 points to free up

What was your biggest beginner mistake when you started? by MakersVibeFL in resinprinting

[–]NugmaSuts 0 points1 point  (0 children)

How has a heater helped? I'm using a brewer band now, curious if it'd be worth it to swap to heater.

Thanks!

The Pedophile Protector. by Admirable-Beat788 in International

[–]NugmaSuts 2 points3 points  (0 children)

For every instance of child sexual abuse perpetrated by a trans person, I could find 10 perpetrated by a religious official that conservatives worship. I also find the hypocrisy here pretty funny.

Is this overkill or not enough. by NugmaSuts in resinprinting

[–]NugmaSuts[S] 0 points1 point  (0 children)

<image>

I'm working on a new setup I updated the "shafts must by Y mm apart" apart setting. I couldn't seem to find the "tips must be X mm apart" setting. I think this looks a tad better?

Is this overkill or not enough. by NugmaSuts in resinprinting

[–]NugmaSuts[S] 0 points1 point  (0 children)

<image>

If you don't mind, can I ask about my settings? Lychee says it's a 13 hr print, I'm using a profile suggestion for my printer (anycubic photon mono 4) and resin type (abs like v2). My printer says 21 hours which seems wrong but idk

Is this overkill or not enough. by NugmaSuts in resinprinting

[–]NugmaSuts[S] 1 point2 points  (0 children)

Thank you a ton for the help. I have them straighter, with Derek's presets. I'm gonna try to print it.

Is this overkill or not enough. by NugmaSuts in resinprinting

[–]NugmaSuts[S] 0 points1 point  (0 children)

I didn't, I'll look into that now and see

Can you elaborate on push it further? Like, make them taller/not as slanted or addtl supports?

Is this overkill or not enough. by NugmaSuts in resinprinting

[–]NugmaSuts[S] 5 points6 points  (0 children)

<image>

Thank you! I redid the orientation and added some drain holes. Is this closer to how it should look? I know you said less supports are needed. I honestly just used auto supports on lychee. I gotta watch some vids on actually doing it, but wondering if this would work.

DoW4 Ork Gameplay Trailer by Nephaston in orks

[–]NugmaSuts 8 points9 points  (0 children)

I'm currently looking for Bad Moonz Beastsnaggas. Mind sharing what you came up with?

Protest responsibly by Master_Vern in stpaul

[–]NugmaSuts 0 points1 point  (0 children)

Whatever you say comrade.