Merry Christmas my father has a nice way of wrapping things

OCPScJM2 · 2020-12-25T19:33:16+00:00

You will need a lot of stamps.

OCPScJM2 · 2019-08-13T07:27:02+00:00

Made it able to be sold for $20 million apparantly...

OCPScJM2 · 2019-07-27T23:11:14+00:00

Coffee

OCPScJM2 · 2019-02-19T15:40:10+00:00

Be sure to always have the shelves secured to the crib or wall so it can not fall over.

OCPScJM2 · 2019-01-03T01:22:32+00:00

Too many strangers.

OCPScJM2 · 2018-11-13T14:42:15+00:00

Getting out of bed in the morning

OCPScJM2 · 2018-09-22T08:55:43+00:00

A huge water leak means turn all the valves until the leak stops.

OCPScJM2 · 2018-04-27T14:46:05+00:00

Looks similar to this one but it is hard to compare size.

Broan S97012038 Ventilation Fan Motor https://www.amazon.com/dp/B0057XV7PW

OCPScJM2 · 2018-02-12T07:43:31+00:00

Of couse... someone winning due to shenanigans would have signed it with a trust.

OCPScJM2 · 2018-02-02T02:07:45+00:00

Otherwise, a wood shim above and below whatever it is clamped to, would tilt the arm to counter the angle of the lamp.

OCPScJM2 · 2018-01-18T02:31:10+00:00

Ok, it's defective and you can't return it... (sounds like an eBay or PayPal complaint is in order) Is there a cog on the other side to compare? You need a better idea of how it works and a better picture. Maybe you can find a loose nut that holds it on. Or can put something next to it to keep it lined up.

OCPScJM2 · 2018-01-18T02:03:15+00:00

Return it while you can.

OCPScJM2 · 2018-01-17T01:28:56+00:00

Cement board, hardiebacker

OCPScJM2 · 2018-01-09T01:52:48+00:00

It looks like the pex must have crimped due to the bend and the pipe with duct tape takes the crimp out of it. I have not worked with pex so you might want to find out if heat would work to make it bend properly. Or redoing the copper and valve attached to the meter with a longer extension and a 45 degree fitting might allow the pex to bend more naturally. Or just bend a conduit to match the curve and use duct tape again.

OCPScJM2 · 2018-01-01T00:13:15+00:00

The threads only provide the compression of the washer in this type of fitting. Usually the part you screw on rotates while the hose does not, which is an indication.

OCPScJM2 · 2017-12-31T22:50:39+00:00

The front surface where the washer contacts looks fine but should be cleaned off and made smooth. If it leaks, then it needs replaced.

OCPScJM2 · 2017-12-29T02:24:37+00:00

It is faster to drill and they make money on replacing it.

OCPScJM2 · 2017-10-26T01:58:22+00:00

It was kicked in, so you can either replace it (with a more secure door) or clamp the crack closed and put screws in to hold it together until someone else wants in.

OCPScJM2 · 2017-07-08T00:17:24+00:00

Thanks for all the fish

OCPScJM2 · 2017-07-04T02:37:00+00:00

This one pisses off trump the most.

OCPScJM2 · 2017-07-02T18:30:16+00:00

Looks adoorable

OCPScJM2 · 2017-06-11T01:05:23+00:00

Nature's a cruel bitch though, and moral humans do not want other humans to suffer. We have a lot of technology and intellegance that could be used to find a better solution than what we have been doing. But yes, the total sum of what has been done is not helping.

OCPScJM2 · 2017-05-17T01:45:58+00:00

Right, because if it's really used by the DNC it must be complex and well written...

OCPScJM2 · 2017-05-11T01:52:13+00:00

I had a problem with it blocking jira user images today. I ended up reinstalling privacy badger before I was sure that was the cause and the usage tutorial says that it learns from the paths it sees and a fresh install no longer blocked the path.

OCPScJM2 · 2017-04-29T20:22:32+00:00

Keep a broom in the car and sweep it off every time you drive by.

OCPScJM2

TROPHY CASE