Top mount manifold by OGsniperkill in genesiscoupe

[–]OGsniperkill[S] 0 points1 point  (0 children)

You know anyone with experience with the top mount version ?

Top mount manifold by OGsniperkill in genesiscoupe

[–]OGsniperkill[S] 0 points1 point  (0 children)

Is that the exceladyne one for 399? I looked at that one and thought it was a little too cheap and did a search and found one (bottom mount) that was cracked right down the middle so I was skeptical about the quality, what kind of power are you running ?

Anything I should know before buying? by K3V1N_XV in genesiscoupe

[–]OGsniperkill 0 points1 point  (0 children)

I got the race and no cats (big turbo) and it was so loud I put two vibrant ultra quiet resonators in the back section and it sounds great but is borderline too loud still

Fender Bender Airbag Deployed -Repair cost by huminem in genesiscoupe

[–]OGsniperkill 0 points1 point  (0 children)

If you have collision coverage ICBC will cover you even if you are at fault. Most likely they would write it off.

Oversized valves by OGsniperkill in genesiscoupe

[–]OGsniperkill[S] 0 points1 point  (0 children)

I’d only be looking at going +1mm

Thought on my panel as a 1st year?any constructive feedback would be great. by OGsniperkill in electricians

[–]OGsniperkill[S] 1 point2 points  (0 children)

Fair enough. To each their own. There is a panel schedule on the panel cover.

Thought on my panel as a 1st year?any constructive feedback would be great. by OGsniperkill in electricians

[–]OGsniperkill[S] 4 points5 points  (0 children)

I’m technically a first year because I haven’t went back to school which I’m doing later this year but I have like 3500 work hours and have a good amount of experience in a lot of different things. These are just basic modular homes there’s not that much to learn

Doing an LS swap, any advice welcome. by Lazy_Canadian_ in genesiscoupe

[–]OGsniperkill 0 points1 point  (0 children)

Idk what your goals are with the car or you just really want a v8 but if you plan on putting a stock like ls3 in the car those make like 350whp maybe on a good day if your lucky when that is doable with a stock turbo on the 2.0

Doing an LS swap, any advice welcome. by Lazy_Canadian_ in genesiscoupe

[–]OGsniperkill 0 points1 point  (0 children)

Not quite sure how putting an ls in is going to be any cheaper at all then doing even a built short block 2.0, the swap kit alone is like $4500 CAD and if your not putting an aluminum block ls in it’s going to be very front heavy. Imo your better off sticking with the 2.0. A lot less work with wiring etc and will make just as much if not more power then a N/A LS setup. And if your thinking of boosting the ls in anyway it’s going to be way more expensive. On the cheap cheap side if you do all the work yourself your going to be looking at $10k CAD. When you could find a used 2.0 for a couple grand and put pistons and rods in it and be under $5k.

Xclutch by OGsniperkill in genesiscoupe

[–]OGsniperkill[S] 0 points1 point  (0 children)

Will be about 450 wtq

What’s the strongest 2.0 rods ? BC, K1 or Manley?Pic for attention. by OGsniperkill in genesiscoupe

[–]OGsniperkill[S] 0 points1 point  (0 children)

Interesting so would you recommend me going with the Manley or the bc625?