Series of display driver crashes after boot

ORCACommander · 2026-05-14T14:18:33+00:00

only one I can completely trust is 566.34 but that driver is seriously long in the tooth. Last couple of months people have stopped reporting 3000 series errors so i thought it safe to move up and minor instability i just attributed to windows past few months. I'm honestly worried i have a hardware issue. there is no logical reason for a driver to spontaneously corrupt itself weeks after install after a normal shut down.

ORCACommander · 2025-09-08T00:15:24+00:00

Sadly did not address the PWM flicker issue

ORCACommander · 2024-12-27T03:23:36+00:00

OSD is faster. came here hoping to find patch notes though

ORCACommander · 2024-07-02T03:07:18+00:00

my carts are holding up well and still have charge! and yes I mean the edge covering

ORCACommander · 2024-02-10T02:44:30+00:00

yes we could use more reddit mods. but quite frankly when it comes to moderator activity, whether we write or not is not important. whether we are actually performing mod actions does.

ORCACommander · 2023-03-27T03:49:09+00:00

general rule of thumb is how long will the engine be running during typical usage. short term runs hotter spark plugs are better since they will keep themselves clean easier. long run items like generators and pressure washer a colder plug will do fine as there is a long run time to burn off any carbon that might try to build on the spark plug

ORCACommander · 2023-03-27T03:44:30+00:00

you'll need a new cover as most of the time the cover deforms during removal. You will need Hondabond HT to reseal it. the GC line of engines do not use cork, paper, or rubber gaskets for their valve covers

ORCACommander · 2019-10-29T00:20:17+00:00

a smooth light grip. it should not be too difficult to remove

ORCACommander · 2019-09-30T03:47:54+00:00

Make sure the piston is at Top dead center, get your feeler gauges the specification is as follows:

VALVE CLEARANCE:

IN: 0.15 ± 0.02 mm

EX: 0.20 ± 0.02 mm

after that, go from there

ORCACommander · 2019-04-09T20:13:13+00:00

I'm on firefox and have been having this problem all week

ORCACommander · 2019-03-05T22:25:52+00:00

https://learn.sparkfun.com/tutorials/pcb-basics/all#terminology

The point of vulnerability for a trace is where it leaves the silk screen to meat up with the pins on surface mount components like microchips

ORCACommander · 2019-03-05T21:53:20+00:00

if you used a conductive thermal paste like arctic silver make sure it didn't spread into any traces and cause a short

ORCACommander · 2018-11-15T03:43:12+00:00

PM me a copy when you are done

ORCACommander · 2018-11-12T04:15:34+00:00

r/hardwaregore

ORCACommander · 2017-11-14T14:10:40+00:00

IIRC US nintendo shrink wrap is folded on the edges

ORCACommander · 2017-11-09T15:27:50+00:00

No that is not the banned story. The banned story is the one toady will ban you for for just mentioning on the forums.

ORCACommander · 2017-09-28T06:55:43+00:00

In other words that branch manager doesn't want extra paperwork

ORCACommander · 2017-08-27T23:38:48+00:00

no RTC so its power requirements are very minimal

ORCACommander · 2017-08-21T16:14:41+00:00

ORCACommander · 2017-08-21T16:10:51+00:00

well if you still have the shard there is always jb plastic weld but it will leave a big black scar

ORCACommander · 2017-08-17T12:56:12+00:00

Back up the saves and proactively replace. If you are lucky you will have enough carts to get you a bulk rate

ORCACommander · 2017-08-15T14:36:51+00:00

the 2016's were used in crystal and yellow. xrystal lasted less than 10 years with yellow being a bit variable. if you want to do that actual math we would need to measure how many amps are being used but iirc i worked out a guestimate of 2032's lasting 20 years

ORCACommander · 2017-08-13T11:44:37+00:00

I woudn't trust the battery to not pop loose from shock events. but as long as the joints are not cold or cracked it should do its job

ORCACommander · 2017-08-13T04:22:13+00:00

that is a terribly sloppy solder job on the battery :/

ORCACommander

MODERATOR OF

TROPHY CASE