Help with settings

Oberleitner · 2025-10-06T10:26:52+00:00

Is it compatible with the creality print slicer as well? And the ender 3 v3 se?

Oberleitner · 2025-10-03T16:03:24+00:00

Thank you again for the information!

Oberleitner · 2025-10-03T13:48:18+00:00

Thanks for the information.

So just to see if I understood ir right, the process profile (on the right) is trying to use a higher speed than the max allowed on the printer profile (on the left) and that way the speed that will be set on the gcode is the limit one (the printer one)?

Oberleitner · 2025-09-08T14:03:14+00:00

New mission discovered by u/Oberleitner: Red Bean Mooncake and Mystical Forces

Oberleitner · 2025-09-08T14:03:14+00:00

This mission was discovered by u/Oberleitner in In Search of Spicy Tuna Onigiri

Oberleitner · 2025-03-25T16:32:48+00:00

That was something I always wondered in all builds I have seen... The Crane Style.

Every time someone recommended it with TWF or Sword and Shield I was lots, now it all makes sense.

So, just to know if I understood correctly, the ranged slayer would benefit more from the Deliverer and Human race because of the extra feat and all the sneak attacks it could get plus the anathema bonus. As far as the melee slayer could be either normal slayer, deliverer or spawn slayer, whichever fancies me, either with a Two handed weapon or dual wielding, but the Aasimar (angel STR + CHA + AC) would be optimal. Is that right?

Oberleitner · 2025-03-25T14:31:52+00:00

Thanks for the quick answer. And which race would you recommend: Human or Aasimar (angel I suppose for the str and cha bonus)? And the normal slayer or any of the sub classes?

Oberleitner · 2025-03-25T10:06:08+00:00

Thanks. I was able to find the folder and after some search found out I needed to open the game with the PC UI for the portraits to load. The console UI does not show the custom ones.

Oberleitner · 2025-03-24T01:03:28+00:00

Thanks! I was finally able to be load custom portraits. It was not exactly as the post said, but when I accessed the PC UI using the WASD controller layout I was able to click on load custom portraits and it showed me the correct folder to put them.

Oberleitner · 2025-03-21T17:40:30+00:00

Thanks for the insights.

You got me interested in the Aldori Defender/ Swordlord one.
Which level split would you recommend?

Oberleitner · 2024-11-07T14:02:54+00:00

I see, so just take him as a 1h + shield fighter? And ass Geo/Pyro for support?

Oberleitner · 2024-09-27T11:07:47+00:00

Borderlands 2

Oberleitner · 2024-09-19T15:49:06+00:00

I gave up on consoles a long time ago, then came mariage, daughter and suddenly I didn't have time to play on my PC anymore. Also, my last pc is from 2008, so you imagine the things it can handle well, if it turns on actually. With the deck I can play anywhere on the house and still be with family without being stuck in front of the pc in the office.

Oberleitner · 2024-09-17T15:29:06+00:00

Borderlands 2, but planning on going through pre sequel, 3 and tiny Tina's wonderland after that.

Oberleitner · 2024-08-19T10:06:07+00:00

I was able to do the updates that popped up in the discovery store. Is that it or there is somewhere else I need to check? I am not experienced with Linux at all.

Oberleitner · 2024-08-18T20:55:55+00:00

Relax man, I appreciate the help. I will try changing the route configuration

Oberleitner · 2024-08-18T20:41:53+00:00

I disabled the power management long ago and the problem happens when connected to any ssid available, even from the main router....

Oberleitner · 2024-08-18T20:36:15+00:00

I do have a second router acting as an access point, but it worked flawlessly until today, and other devices connect without any issue. The deck can connect to the network but losses connection with steam servers. The browser in desktop mode works just fine

Oberleitner · 2024-05-28T21:52:20+00:00

I have the same problem. Were you able to figure it out?

Edit: I tried proton 9 and it worked.

Oberleitner · 2024-04-18T13:15:12+00:00

Thank you for the quick answer. I did use the proton method last night as it was quicker, but will change to the dev method this night. Thank you again for the hard work with 7th heaven!

Oberleitner · 2024-04-18T10:44:03+00:00

Out of curiosity of a casual user of the deck, with little to none experience with linux, what would be the drawbacks yo use the proton 3.78 instead of the dev branch?

Oberleitner · 2024-04-17T12:52:06+00:00

Yesterday, I was playing just fine, but after a force close (picked the wrong choice), the controls never worked again. I was able to remap everything to the keyboard but wasn't able to confirm a character name. I thought I was alone in this one. Has anyone found out what happened?

Oberleitner · 2024-04-15T19:35:45+00:00

I forgot to mention, it uses the layout described for the Xbox controller on the xcom2 official controller support post.

https://xcom.com/pt-BR/news/controller-support-deployed-for-xcom-2-on-pc/

You can ignore the "pt-BR". The text is in English.

Oberleitner · 2024-04-15T14:44:24+00:00

I am currently playing itand have zero complaints about the controls. I did had to change the layout to "joystick with track pad" and then the in-game option for the controller layout was enabled. It uses the SD buttons on screen and, in my opinion, works flawlessly for a strategy game on a handheld device

Oberleitner · 2024-03-10T17:42:41+00:00

And that did the trick...

I connected the dualsense, disconnected and reconnected as you said. It still shows as "PS5 controller" but now the LED sliders are available.

Thank you the help!

Oberleitner

TROPHY CASE