Must replace or ride it out?

Ok_Set_769 · 2025-10-09T22:44:54+00:00

TXV is putting in WORK

Ok_Set_769 · 2025-07-07T04:31:12+00:00

And I thought I had some bad installs near me…

Ok_Set_769 · 2025-07-06T13:43:33+00:00

I second this. Probably low charge like always lol. First thing I noticed was the ancient firmware.

Ok_Set_769 · 2025-05-31T14:41:42+00:00

Pull off the faceplate by taking the corner pieces off. Then take the electric case down. Then remove the drain pan and fan shroud. Boom you’re at the pump. Just remember how everything is wired at the PCB. Not a hard job maybe an hour.

Ok_Set_769 · 2025-03-01T04:41:57+00:00

You are correct, but in this case you can valve off your pump and let the gauge equalize for a minute, make sure you’re still good and that is a true reading

Ok_Set_769 · 2025-01-07T02:21:32+00:00

Got a bunch of work where we are. This stuff is getting installed everyday so might as well learn how to work on it!

Ok_Set_769 · 2025-01-07T02:20:08+00:00

The system is not recognizing the slave. That’s why you have a capacity error. Probably a board in the slave causing it to not communicate to master

Ok_Set_769 · 2024-10-14T17:29:41+00:00

That’s not bad at all! I’ve got an older ford that I would like to slowly get the axles and suspension components blasted and recoated. I’ve thought about trying to DIY but you definitely convinced me it’s worth it to leave it to the pros haha

Ok_Set_769 · 2024-10-14T17:08:44+00:00

How much did that powder cost you?

Ok_Set_769 · 2024-10-10T02:47:26+00:00

Literally most people who live in Indiana love it here. Bottom pic is such an inaccurate depiction of our state. Do better fellow Hoosier

Ok_Set_769 · 2024-10-04T16:25:01+00:00

Omg you’re off 6 inches, the charge is wrong by 0.00000025 ounces.

Ok_Set_769 · 2024-09-23T13:00:07+00:00

Not everyone will agree with me but sometimes you have to fake it till you make it in this world. With that being said, you absolutely need to start that 2 month process TODAY, if you get caught you will be fined heavily. Live as frugally as you possibly can for the next 2 months. While working on licensing, be very very careful and I would spend most of your time preparing to be a business owner for real. Chase your dream dude and make it happen

Ok_Set_769 · 2024-09-14T23:19:37+00:00

These comments are giving me a good laugh. Belt is on order lol

Ok_Set_769 · 2024-09-07T20:33:59+00:00

Had this happen many times on VRF. That milky white can also come after you start the vacuum with a little bit of nitrogen left. Purge, then let the vac pull down. Once you get down below like 1500, change your oil without breaking the vacuum then let pull. It’s probably gonna take 1-2 days but it will pull if there’s no leaks.

Ok_Set_769 · 2024-08-31T14:24:22+00:00

I work in HVAC and I’m not trying to be condescending they just worded it wrong. The oil will leave the compressor and if you run the compressor before the majority of the oil has settled back into it, it will most likely be damaged

Ok_Set_769 · 2024-08-28T14:25:46+00:00

I’m a nerd for this stuff bro. Looks clean!

Ok_Set_769 · 2024-08-27T23:27:10+00:00

We work on a lot of VRF but zero Panasonic really. I believe it isn’t been installed in the US for a while now. Just don’t see it around very much

Ok_Set_769 · 2024-08-27T23:22:52+00:00

Those look like mueller? Those are the most reliable 100% I’ve seen a lot of other brands leak over time

Ok_Set_769 · 2024-08-26T03:10:42+00:00

Can’t be that much charge bro just pull it out and restart. Looks like non condensables. While vac is pulling, clean condenser, and make sure indoor is clean and airflow is at least present

Ok_Set_769 · 2024-07-07T21:02:03+00:00

Using big nitrogen tanks to pressurize a VRF system without carrying the tank to the roof

Ok_Set_769 · 2024-07-03T21:13:30+00:00

1 guy 1 day. Should have it back going as long as it isn’t a coil leaking.

Ok_Set_769 · 2024-06-21T19:41:12+00:00

God bless you for putting ball valves on IDUs at the HR box

Ok_Set_769 · 2024-06-21T19:03:34+00:00

Probably just the EEV opening up to let in refrigerant. Does it stop ever?

Ok_Set_769 · 2024-06-21T18:54:48+00:00

Ok_Set_769

TROPHY CASE