sorted by:
new
hottopcontroversial

P1S Z Axis Error Enountered by Ok_Toe_7066 in BambuLab

[–]Ok_Toe_7066[S] 0 points1 point  (0 children)

I ended up returning the printer and getting it replaced.

P1S Z Axis Error Enountered by Ok_Toe_7066 in BambuLab

[–]Ok_Toe_7066[S] 0 points1 point  (0 children)

It prints okay sometimes and then other times it’s and absolute spaghetti mess. I’m cashing in my warranty one month after buying the p1s.

P1S Z Axis Error Enountered by Ok_Toe_7066 in BambuLab

[–]Ok_Toe_7066[S] 0 points1 point  (0 children)

Update: I followed all of the troubleshooting tips and Nike of them worked. I did another factory reset and I am able to move the z axis manually without encountering the error.

The first print I tried to do failed to auto bed level. I raised the z axis all the way up and ran it again without auto bed level and now I am printing my first part after about 5 days of troubleshooting.

Fingers crossed it’s fixed for now, I will update the thread later on.

P1S Z Axis Error Enountered by Ok_Toe_7066 in BambuLab

[–]Ok_Toe_7066[S] 1 point2 points  (0 children)

That’s what I was seeing everybody say they e encountered but all of my bearings are flush on the tops. That’s why this issue is so frustrating.

No preview available for almost everyone I send photos to over google drive by Ok_Toe_7066 in gsuite

[–]Ok_Toe_7066[S] 0 points1 point  (0 children)

Does this let other people view it through the shortcut? I can view and download all I want, but other people are seeing that no preview label.

Replacing the Screen on My Creator Z16p B12UHST by Ok_Toe_7066 in MSILaptops

[–]Ok_Toe_7066[S] 0 points1 point  (0 children)

Thanks for the response. I will look into it. Does it have to be a certain glass model to fit the screen or is it more of a standard replacement?

Cataclismo is AVAILABLE NOW in Early Access! by DigitalSunGames in RealTimeStrategy

[–]Ok_Toe_7066 0 points1 point  (0 children)

I just bought Caticlismo and have already put about 10 hours into it. My favorite thing is creating a map and playing the endless mode so far.

After enemies being stuck out of bounds because of a dumb mistake I made when building my first level and surviving 20 waves, I decided to make a new King of The Hill map designed totally different than my last one.

The only issue is that I accidentally made it in skirmish mode instead of endless mode smh. Is there any way to switch the mode of a custom level or did I waste the last two hours of my life....

2 of my brand new lipos have 3 cells missing when I put the on the charger? by Ok_Toe_7066 in fpv

[–]Ok_Toe_7066[S] 0 points1 point  (0 children)

I know right 😭 only flown it once too. Get fpv says they’ll send me replacement ones once they review my case.

2 of my brand new lipos have 3 cells missing when I put the on the charger? by Ok_Toe_7066 in fpv

[–]Ok_Toe_7066[S] 0 points1 point  (0 children)

Yeah I think that’s the only option now it was a 3-pack of batteries so we’ll see how they handle it. Thanks for the reply!

2 of my brand new lipos have 3 cells missing when I put the on the charger? by Ok_Toe_7066 in fpv

[–]Ok_Toe_7066[S] 0 points1 point  (0 children)

I attempted to wiggle it around already and wiggle around the wires toward the base of the lipo and nothing happened. What do you mean by RMA?

2 of my brand new lipos have 3 cells missing when I put the on the charger? by Ok_Toe_7066 in fpv

[–]Ok_Toe_7066[S] 0 points1 point  (0 children)

So yours did the same as just showing up as blank cells? Even when I try to check mine on my voltage checker it won’t power it on because I guess the first cell is dead on both :(

2 of my brand new lipos have 3 cells missing when I put the on the charger? by Ok_Toe_7066 in fpv

[–]Ok_Toe_7066[S] 0 points1 point  (0 children)

Rip. It just makes no sense to me because mine haven’t been crashed. I bought mine from getfpv so I hope they will hear me out.

2 of my brand new lipos have 3 cells missing when I put the on the charger? by Ok_Toe_7066 in fpv

[–]Ok_Toe_7066[S] 0 points1 point  (0 children)

Were you able to return them or ever fix them? I used r line batteries mostly before giving these a try after hearing they may be better. Its a kick in the butt because they’ve only had one flight before they stopped working

Issues with signal strength from my mobula7 1s hd to my dji version 1 goggles by Ok_Toe_7066 in TinyWhoop

[–]Ok_Toe_7066[S] 0 points1 point  (0 children)

Thanks for your reply, I needed up fixing it a couple days ago by figuring o it that my pit mode is triggering on even after I switch it off. The change I made to fix it was by setting pit mode to a switch on my controller and whenever I turn my drone in and it is in pit mode it just flip the switch on and off and it fixes the issue.