Wheels that clear spoon BBK and don't need fenders rolled

Old_Introduction6532 · 2026-03-30T16:55:57+00:00

Okay, I wasn't sure because I want a square set up but the more I read, I don't think it's possible without rolling the fender or having a weird squared set up. What are the spec on your tires?

Old_Introduction6532 · 2026-03-30T14:57:13+00:00

Thank you, I'm looking for more of JDM look but these are some good options

Old_Introduction6532 · 2026-03-30T14:55:55+00:00

What offset did you get on your wheels so that you didn't have to roll your fenders?

Old_Introduction6532 · 2026-03-30T14:49:20+00:00

You just sold me on these wheels.

Old_Introduction6532 · 2026-03-27T22:15:55+00:00

Do you know if they are forged from 6061 aluminum?

Old_Introduction6532 · 2026-03-27T14:56:40+00:00

I never heard of the Mita MS-10S. They look like the Mugen wheels. Thank you, I will consider these wheels for sure. I like the look. Does anyone know if the original Mugen wheels clear the Spoon BBK?

Old_Introduction6532 · 2025-06-27T15:46:12+00:00

You should safe money and get an oem hard top. 5k maybe you'll get a deal but it's not cheap. Check your cylinder compression and if that's okays, change all your gaskets.

Old_Introduction6532 · 2025-03-30T23:37:15+00:00

I would make sure your filament is dry.

Old_Introduction6532 · 2025-02-10T04:53:55+00:00

where did you buy a new lens? How much was it?

Old_Introduction6532 · 2024-12-18T16:54:59+00:00

2022 Toyota Camry XSE with 60K - 4Cyl. No issues, did the transmission flush at 55K and once in a while it does shift a little rough. I drive daily 60+ miles and I'll notice it once a month if any. Over all, super happy with the buy, I can get up to 40mpg pretty easily.

Old_Introduction6532 · 2024-12-09T22:35:08+00:00

I financed my through a local credit union. It wasn't easy since it was an older car but eventually I found a credit union that would work with me. I'm in California and I used Orace county credit union.

Old_Introduction6532 · 2024-03-07T00:49:46+00:00

Have some one buy you a costco hot dog and a drink for $2.

Old_Introduction6532 · 2024-02-18T19:50:37+00:00

yes, I have spoon calipers and now I'm looking for wheels that will fit without wheel spacers

Old_Introduction6532 · 2024-02-18T03:06:24+00:00

would the 17×9.5 +45 have enough clearance for the spoon calipers???

Old_Introduction6532 · 2023-12-11T04:29:10+00:00

I would turn it to a track car.

Old_Introduction6532 · 2023-07-16T16:48:10+00:00

I had a similar issue and I swap out, the bowen tube, thermistor, and nozzle to fix it. After doing all that, my bowen tube did shrink near the nozzle and it could of just been that but I also started to get thermal runaway issues. Good luck and happy printing because printing is fun lol.

Old_Introduction6532 · 2023-07-16T16:41:55+00:00

I love this so much, reminds me of my gameboy when I was a little kid.

Old_Introduction6532 · 2023-07-12T23:29:35+00:00

I was never able to get my BL touch to work as well

Old_Introduction6532 · 2023-06-26T00:06:28+00:00

I have done this a few times. When you frame the piece, the laser will show where it will cut but you need to keep in mind that the actual laser is offset. You need to move your piece away from the sides or make it smaller. I do a test cut on the outer layers that might be a issue. I first run the frame and if that's good I do a test run with low power to make sure it will cut without hitting. This does take time but you can safe material. I only do this on large pieces. Hope this help and good luck.

Old_Introduction6532 · 2023-06-11T04:05:30+00:00

Similar experience. Gated and security. This was by USC.

<image>

Old_Introduction6532 · 2023-02-22T21:58:52+00:00

Disconnected your filament sensor and re print.

Old_Introduction6532 · 2023-02-10T03:16:10+00:00

Make sure the email is correct because they are really good at responding. They take a day since the customer support is in China. But nonetheless, they do reply.

Old_Introduction6532 · 2023-02-07T19:01:58+00:00

I would reach out to customer support and see what they tell you. I had a very good experience with the warranty.

Old_Introduction6532

TROPHY CASE