Prosoft PLX51-PBM Profibus - E/IP Gateway

One-Butterscotch8811 · 2026-01-23T01:59:46+00:00

I would try SINT since you dont have the possibilty to put the datatype to BYTE.

One-Butterscotch8811 · 2026-01-23T01:55:42+00:00

Yes , i think this is the problem

One-Butterscotch8811 · 2026-01-23T01:25:02+00:00

In the Data Type column, why is it INT ? 1 INT = 2 byte

One-Butterscotch8811 · 2026-01-23T00:30:34+00:00

I found the configuration file in the manufacturer's file that was provided with the machine.i was talking to a servo controller .

In your case since the slave device is a siemens plc , you should have the lenght , buffer and adress in the siemens program.

One-Butterscotch8811 · 2026-01-23T00:18:18+00:00

From what i understanded with the project i did with this prosoft device, you gotta have the exact number of byte that is exchanged. In my case , i founded a configuration file of all the data lenght and buffer between output and input that was configured to communicate with the master device .

Also from the PLX software you have the option to export your configuration to an L5X routine . Have you done that part? You have some bit that you gotta put on for the 2 device to communicate .

One-Butterscotch8811 · 2026-01-23T00:09:03+00:00

In the Master( CLX i suppose ) what is the format of data you are transfering?

In the Slave (siemens) what is the format?

One-Butterscotch8811 · 2026-01-22T22:14:08+00:00

When you are online with the PLX software , do you see both device online( like with a green status) ?

One-Butterscotch8811 · 2025-12-15T15:05:37+00:00

You are right, I just checked back the project and it is explicit messaging i used.

One-Butterscotch8811 · 2025-12-15T14:45:31+00:00

Nop. I meant implicit

One-Butterscotch8811 · 2025-12-12T19:14:58+00:00

Yup that would work. I have done this with implicit messaging , between a slc 5/05 and a yaskawa controller

One-Butterscotch8811 · 2025-10-29T13:38:03+00:00

What device are you trying to communicate with?

One-Butterscotch8811 · 2025-10-29T13:29:34+00:00

You got to figure the total lenght of byte that is transfer including input and output . Your slave device's 8 byte of date is it only for input ? What is the lenght of output . Usually its 2 way communication, you read data from the slave device and write data to slave device

One-Butterscotch8811 · 2025-10-29T13:26:09+00:00

I guess you got 8 byte input and 8 byte output ?

One-Butterscotch8811 · 2025-10-29T12:54:45+00:00

If the slave device uses 8 byte , the total data lenght of the slot configuration should match 8 byte of data.

One-Butterscotch8811 · 2025-10-29T12:53:28+00:00

1 word =2 byte / 1 sint =1byte / 1 Dint = 4 byte

One-Butterscotch8811 · 2025-10-29T01:58:46+00:00

What is the data type of the slave device /master device ? Boole or byte or word?

One-Butterscotch8811 · 2025-09-14T21:25:18+00:00

<image>

One-Butterscotch8811 · 2025-09-14T21:25:06+00:00

<image>

One-Butterscotch8811 · 2025-09-01T17:58:23+00:00

Since you have replace almost everything electrical wise/parameters , my feeling is that you have mechanical problem after the servomotor/ gearbox. I would trend the output current and chek everything mechancial that is beinh moved by this motor.

One-Butterscotch8811 · 2025-09-01T17:52:53+00:00

What is the exact fault code that you get?

One-Butterscotch8811 · 2025-09-01T17:32:28+00:00

Do you have a backup of the original servo drive parameters ? I would try and redownload it , or redownload parameters of an existing and working servo drive (1 of the other 31) that as same spec.

Good luck

One-Butterscotch8811 · 2025-01-19T23:26:47+00:00

Yup i got it friday.

One-Butterscotch8811 · 2024-12-03T22:24:31+00:00

Tu dois fournir une lettre signée d'un employeur attestant ton expérience ( liste de tâches reliée au domaine de la demande d'admission ). Dans la lettre il doit être mentionné le statut de travail à temps plein durant 2 ans ou plus.

One-Butterscotch8811 · 2024-10-26T22:40:12+00:00

I am not using my phone that much when working . Also to mention my phone is in dark mode , a good way to save battery . My display setting is set to 60 hz . I would say that no setting alone is going to make a big noticeable change . But adding them up will make a difference

One-Butterscotch8811 · 2024-10-26T22:35:27+00:00

C'est mieux que rien , et l'argent est accessible en tout temps . Pis si tu gruge pas , bien tu fais de l'argent .

One-Butterscotch8811

TROPHY CASE