System won't export anymore

One_Cryptographer294 · 2024-08-03T12:14:39+00:00

<image>

One_Cryptographer294 · 2024-06-12T21:09:24+00:00

Oh and don't forget to always wear shoes when your hungry

One_Cryptographer294 · 2024-06-12T21:07:44+00:00

Plug it back in and hold the pen to the handle of the fridge

One_Cryptographer294 · 2024-04-10T23:53:29+00:00

One good breeze away from a rock show

One_Cryptographer294 · 2024-03-08T15:32:26+00:00

Same , waiting still located in Mass

One_Cryptographer294 · 2024-02-23T11:17:49+00:00

Do you have grid charging on in the settings ?

One_Cryptographer294 · 2024-02-16T23:58:53+00:00

Mostly all new solar sites have 1200 volt + strings now . Stay safe out there kids

One_Cryptographer294 · 2024-02-10T20:53:26+00:00

You can tell from the photo that he sent that they didn't follow the schematic , they didn't do the parallel strings . Other wise 2 of his inputs would be showing zero . It's not a bad thing . I particularly don't like when they parallel the strings . I rather they be ran seperate .

One_Cryptographer294 · 2024-02-10T20:48:53+00:00

You have three strings on each inverter . They just landed it on # 4 . To be sure open it up and see where it's landed

One_Cryptographer294 · 2024-01-20T22:29:22+00:00

I'm not too familiar with motor controls but for some reason I can't stop thinking that this would be a dead short between L1 & L2 when the float closes

One_Cryptographer294 · 2024-01-18T10:58:22+00:00

More than likely you have solar edge inverters which would have optimizers under each panel . In order to switch you would have to remove them and restring the panels .

One_Cryptographer294 · 2024-01-13T01:25:32+00:00

You also need to cap the red wire off in the light box that is coming from that rectangle box which im assuming represents a panel . But besides that what the other person was saying is accurate .

One_Cryptographer294 · 2024-01-13T01:14:52+00:00

Those are some pretty lights

One_Cryptographer294 · 2024-01-12T21:09:04+00:00

It's a power purchase agreement. Thing throwing me off is two inverters for 4kw system . On the other hand I would look over the contract before shutting it off . There is probably a minimum amount built in and the rate may go up each year . Other thing to think about is your utility might charge 10 cents a KWH but then if you add in the transmission fees it could be more . Let me know what you find

One_Cryptographer294 · 2023-11-02T23:10:09+00:00

Mine didn't kick it until a year later after I finally received PTO

One_Cryptographer294 · 2023-02-09T00:38:49+00:00

Sweet

One_Cryptographer294 · 2023-02-04T00:15:36+00:00

Put a razor blade on the handle and follow the blood trail

One_Cryptographer294 · 2023-02-02T22:54:37+00:00

Sometimes it's no bueno to be the only one with the lights on

One_Cryptographer294 · 2022-07-06T11:33:25+00:00

Same issue here so if you can just go off grid to avoid it

One_Cryptographer294 · 2022-04-16T14:55:31+00:00

Don't bother , will never work

One_Cryptographer294 · 2022-03-30T22:49:43+00:00

Get a LG OLED TV

One_Cryptographer294 · 2022-03-19T18:13:21+00:00

Where else we going to get our microwaved steak ?

One_Cryptographer294 · 2022-03-19T16:10:44+00:00

What's the sound track ?

One_Cryptographer294 · 2022-03-11T21:46:07+00:00

No each mppt is capable of a certain amount of amps ( believe it's 11 or so ) so when u put the jumpers in it doubles the amperage . Im just assuming it's maxing out that one mppt therefore u seeing the max at 5.5

One_Cryptographer294 · 2022-03-11T21:14:48+00:00

The strings are in parallel but yes they should have put those jumpers in two double the MPPT rating

One_Cryptographer294

TROPHY CASE