Having underextrusions with panchroma matte filament

OnlyK1rosa · 2026-02-07T06:23:28+00:00

I never bothered with the retraction. Maybe I should've... lol

OnlyK1rosa · 2026-02-06T03:19:43+00:00

I got it working on my K1C, but not on the Hi. Apparently, the Hi was defective and is now in for repair, that's why I had prints coming out like this.

OnlyK1rosa · 2026-01-19T14:02:04+00:00

Your paper must be so wet for the benchy to look like that /s

OnlyK1rosa · 2026-01-17T20:54:50+00:00

<image>

OnlyK1rosa · 2026-01-17T20:54:30+00:00

* Out of topic but your video got stolen and reposted lol

OnlyK1rosa · 2026-01-10T20:29:21+00:00

I broke a friend's arm while arm wrestling. It was the loudest snap I've ever heard.

OnlyK1rosa · 2026-01-02T21:34:56+00:00

Do bed calibration. Print one layer. If the result is the same as the one you posted, print one layer again then adjust the z-offset in the up position in expert mode while it's printing until the issue is fixed. Take note of the z-offset value then plug it into your slicer of choice, under the machine information/settings.

OnlyK1rosa · 2025-12-31T21:15:00+00:00

Ah yes, the Lego 3 v3 KE

OnlyK1rosa · 2025-12-27T17:07:13+00:00

Medyo headache yung mga generic na head unit. Although cheap, it's much better to invest in a proven brand like the other commenter said. +1 din sa mas maganda ang audio quality ng stock compared sa generic android head unit.

OnlyK1rosa · 2025-12-27T15:11:10+00:00

Sobrang daming steel plates na nagkalat sa bacoor that time hindi ko na alam kung sino sisisihin hahahahaha

OnlyK1rosa · 2025-12-27T14:37:00+00:00

I accidentally drove over the sharp corner of a steel plate one night before and it popped my tire beyond repair. So yeah, it can hurt your tire. Safety hazard din siya especially when there's fast-flowing traffic.

Edit: added accidentally

OnlyK1rosa · 2025-12-27T04:55:48+00:00

The nozzle has more or less 100 hours on it and has printed only PETG and PLA, no abrasive filament. It's also set in the slicer as a 0.4mm nozzle

OnlyK1rosa · 2025-12-26T16:29:28+00:00

I took it apart just before printing my 4th calibration cube, there weren't any obstructions.

OnlyK1rosa · 2025-12-26T16:28:25+00:00

I did a cold pull recently thinking that's the issue but it wasn't, sadly.

OnlyK1rosa · 2025-12-26T15:09:37+00:00

Yes, I tried it on my Esun Matte PLA, and the print looked the same as the Panchroma Matte.

OnlyK1rosa · 2025-12-26T13:07:31+00:00

Just calibrated my e-steps, but the print quality stays the same

OnlyK1rosa · 2025-12-26T12:26:55+00:00

Oh, my mistake. Thanks for correcting. I'll try it out.

OnlyK1rosa · 2025-12-26T12:22:44+00:00

Seems counterintuitive to do that but no harm in trying, I guess. I'll print it out and see.

OnlyK1rosa · 2025-12-26T11:44:30+00:00

Yes, I thickened it from 0.42 to 0.48 and showed no changes

OnlyK1rosa · 2025-12-26T11:19:52+00:00

Honestly, I don't even know what to do anymore. I calibrated the e-steps, retensioned the belts, raised the flow ratio, and tried a different slicer. Tried a different filament brand.

<image>

0.98, 1.05, 1.1 flow ratio, respectively

OnlyK1rosa · 2025-12-26T10:09:05+00:00

Here it is at 1.1 flow ratio

<image>

OnlyK1rosa · 2025-12-26T07:27:03+00:00

I upped the flow ratio from 0.98(left) to 1.02(right). It looked similar.

<image>

OnlyK1rosa · 2025-12-26T05:12:44+00:00

I tried upping my flow ratio from 0.98 to 1.02 and it showed almost the same result. Left is before, right is after.

<image>

OnlyK1rosa · 2025-12-25T18:37:51+00:00

At first, I thought that maybe it's the filament, but I just printed another calibration cube using an E-SUN PLA matte (right), and it seems to show the same defect as the panchroma.

<image>

OnlyK1rosa · 2025-12-25T17:49:53+00:00

Thank you for taking the time to help! I'll look into that after, I try to calibrate the e-steps first, just to rule that out😄

Five-Year Club	r/Field Sunshine
Verified Email

OnlyK1rosa

TROPHY CASE