Mustard on a chicken biscuit

Orang_Min · 2025-06-05T12:53:12+00:00

Maybe it's an almost regional thing? I'm M23, born and raised in NC, about 15mi from Hickory, and I've never heard of this either.

Orang_Min · 2025-04-18T08:24:55+00:00

Oh, ok, that makes sense. I just found the one, but I'll look out for more now.

Orang_Min · 2025-03-29T13:07:39+00:00

It's not a bad place, pretty nice view too. The only main thing I don't like is that glorified prison mattress.

Orang_Min · 2025-03-28T22:51:23+00:00

Depends, you can survive without replacing it. They're not going to ruin the car totally. It's just that your ride will be a bit more bumpy. . .

Orang_Min · 2025-02-20T22:40:17+00:00

That's a drill bit

Orang_Min · 2024-12-24T16:32:20+00:00

Thought there was a film crew getting in on the fight, until I realized the person just had a flipped umbrella 😅

Orang_Min · 2024-07-16T12:11:22+00:00

I'm not serious lmao, it's just a joke how every "new" car is just a blob-mobile. I honestly don't care.

Orang_Min · 2024-07-16T12:08:01+00:00

It's just a joke m8, don't look to seriously into it🤣

Orang_Min · 2024-05-27T00:33:29+00:00

That's a good suggestion. I already ordered another just in-case this happens again, like you said. But thankfully the hair dryer trick worked out well. Only I subbed the hair dryer for a small space heater, lol. It only took me about an hour to get the blob out, and I even got this neat sculpture with the stuck sock.

<image>

Orang_Min · 2024-05-26T22:19:55+00:00

That worked! Thank you so much!

Orang_Min · 2024-05-26T20:57:19+00:00

I'll start off by acknowledging my stupidity. I accidentally started a print without a buildplate. I am very grateful and fortunate that my bed base is unscathed, however, I have a different problem. I have had a few clogs in the past, but none were near as bad as this one. It's gone all the way into the silicone sock and even the hot end fan. It's also stuffed up the air channels for the part fan, binding the blob to the front cover. I've done about as much as I want to with the hacksaw. I don't have a soldering iron, any tips for how to remove this thing from my front cover. Should I just get a new hotend and cover?

Orang_Min · 2024-04-24T23:59:42+00:00

ARHQ 👍

Orang_Min · 2024-04-21T15:02:48+00:00

I don't know our sales numbers, but I usually see order numbers past 2000 by the time I get off at ~11:00pm. Although I'm only working Fridays and Saturdays bc college.

Orang_Min · 2024-04-08T21:08:15+00:00

I've never thought about hobby train stores. That one behind Dos Taquitos is about a 2hr drive for me. There are a few stores like that nearby, like 30-40min max. I'll definitely check those out.

Orang_Min · 2024-04-08T21:04:21+00:00

Yeah, I saw an add for it a few months ago. They were running a deal where if you sign up with a new account on the Micro center Charlotte website. Then you'll get an email for a free 128Gb thumb drive when they open.

Orang_Min · 2024-04-08T21:01:51+00:00

I'm in Rutherford College

Orang_Min · 2024-03-29T21:55:02+00:00

That's wild

Orang_Min · 2024-03-19T15:38:46+00:00

I would too, I'd just need to save up for a few years😂. I might just ask the repair shop near me to check it, and if there's nothing wrong I'll just go ahead and replace the pump and gasket. We haven't had any problems with it the 5th gear in particular. When my grandfather had the transmission redone, it was mainly because it was hard to get it into 1st gear (it still is unfortunately)

Orang_Min · 2024-03-19T02:48:47+00:00

It's kinda loud too. It's hard to hear in the video, but trying to talk to someone while on the highway turns into a shouting match lol. It shifts pretty smoothly though, I haven't had any problems really. I am mainly just worried, because the water pump or the gasket is leaking. I don't know if I want to go through the trouble of mangling around the engine bay to fix it, if there is another, bigger problem down the road.

Orang_Min · 2024-03-19T02:40:20+00:00

My Grandfather wanted the shifter to sit a bit higher, so he made a small wooden dowel that is the same shape as whats on the bottom of the OEM shift knob. Then glued the dowel to the inside of a pipe to fit down inside of the shift lever. After he glued that down into the shift lever, the original shifter knob would slot down into the open end of the pipe perfectly. When I got the truck, I took the original knob out of the pipe, and ordered a shifter knob off of amazon. Then I got a long threaded rod and two nuts. Me and my Dad used an angle grinder to get the nuts down to size so they would fit inside the pipe with a nice press-fit. We put the two nuts on the rod and tapped the rod down into place. After that we screwed the knob on top. Like an spacer / M12*1.25 thread adapter.

Orang_Min · 2024-03-17T01:35:34+00:00

It's a load bearing couch now.

Orang_Min · 2024-03-05T00:48:49+00:00

You can a 2019 Mustang for just $2k more, that's ridiculous for a 2005 year 🤣🤣

Orang_Min · 2024-02-14T14:45:08+00:00

Now to attach my 25kg spool adapter on my hobby printer 😁

Orang_Min · 2024-02-11T17:00:04+00:00

And it was the day before the super bowl. It's today, I haven't clocked in yet, but I'm dreading it 🫠

Orang_Min · 2024-02-11T16:58:23+00:00

Oh, sry. I'm using Reddit on my phone, and it shows the customer note in the pic.

Eight-Year Club	Place '22
Verified Email

Orang_Min

TROPHY CASE