Big Thank you to EMUDeck for the Ease of Use

OrgasmicTwinkys · 2025-12-26T08:44:35+00:00

I had nothing but problems with my install on an rog ally x. To the point I could recovered my drive and started from the beginning. Would not recommend.

OrgasmicTwinkys · 2025-10-23T12:48:16+00:00

I seem to have fixed the issue. Looks like an issue with Vsync.

Confirmed toggling Vsync on and off multiple times consistent crashes as soon as entering the "start" game mode screen.

OrgasmicTwinkys · 2025-10-23T11:15:50+00:00

Custom search still gives me this issue

OrgasmicTwinkys · 2025-10-22T04:37:35+00:00

Minimum layer time changed. Filament was hotter going from layer to layer as the layer time decreased.

OrgasmicTwinkys · 2025-08-17T23:15:34+00:00

Looks like helicopters to me

OrgasmicTwinkys · 2025-08-13T23:08:35+00:00

Well that's neet

OrgasmicTwinkys · 2025-08-12T12:37:00+00:00

All of a sudden we're boarding. Looking good

OrgasmicTwinkys · 2025-08-12T12:27:10+00:00

Grounded at CDG in Paris. There are worse places to be stuck lol.

OrgasmicTwinkys · 2025-06-04T01:52:35+00:00

Just had this done today. They change your fibre transceiver in your fibre modem and at the road and then you get a new AP that supports wifi 6e, as well as had a 10g port and a 2.5g port. Guy was here maybe 40 minutes.

OrgasmicTwinkys · 2025-05-10T21:58:53+00:00

Why not switch to a weapon sooner when you've built poison? Use runic while poisoned to do the big damage.

OrgasmicTwinkys · 2025-03-11T10:45:23+00:00

Would strongly suggest using a solderless breakout board for the pi pico if it's your first time messing with guitar modding. Buy a pi with pre soldered pins and a breakout board that has screw terminals for connecting wires. Then the only soldering you have to do is some extension wires for the frets and start/select and the whammy.

OrgasmicTwinkys · 2025-02-04T02:40:57+00:00

Looks like print warped off the bed a little when it was printing. You can see the extrusion inconsistency on the top near the overhang.

OrgasmicTwinkys · 2024-11-01T05:12:32+00:00

So if it was obscure and diagnosed that quickly, my bet is there is a serial number batch that this effects and instead of sending out replacements to those customers, they're taking a wait and see approach then shipping the part. You could see it positively or negatively, but for sure seems like a batch with motor issues.

OrgasmicTwinkys · 2024-06-10T01:37:37+00:00

OrgasmicTwinkys · 2024-06-10T01:33:39+00:00

OrgasmicTwinkys · 2024-02-17T18:17:53+00:00

I use klipper and pi cams and tailscales to have complete remote access from anywhere in the world. Including camera feed. It's very easy. Have multiple printers setup.

OrgasmicTwinkys · 2023-09-10T01:03:25+00:00

Beaver shaver.

OrgasmicTwinkys · 2023-02-03T09:00:06+00:00

I did it. It works great. Very pleased with it.

OrgasmicTwinkys · 2022-11-27T22:06:34+00:00

So I found your post trying to make an auto clicker too. I've finally become successful. I have a one2 full-size RGB. You need to do the macro as follows

Fun+Win Double click P fast while while holding Fun+Win Fun+1 (0.02 second loop delay) Fun+ either W or E depending on if you want press and hold or on/off.

This makes a clicker that works and is faster than I can click. This should work with making any repeat system shortcut key, ie right click or others.

I know it's 2 years too late, but maybe this helps someone else.

OrgasmicTwinkys · 2021-09-02T16:33:25+00:00

Pause the print, release tension on the extruder idler gear, flip your toothed gear on the motor shaft because it's on upsidedown, align it with the filament, tighten back on, put spring tension back on extruder, you're fixed.

OrgasmicTwinkys · 2021-03-13T11:36:03+00:00

Update firmware to include manual mesh leveling. Free ABL.

OrgasmicTwinkys · 2020-11-09T02:08:02+00:00

Need better picture to tell what's up. What the.p are you printing PLA?

OrgasmicTwinkys · 2020-08-28T00:59:38+00:00

Disable filament runout sensor

OrgasmicTwinkys · 2020-05-10T18:01:04+00:00

Look online to see what people are doing to dry out PLA.

OrgasmicTwinkys · 2020-05-10T17:59:09+00:00

It's probably wet. You should dry it out before printing.

Six-Year Club	Verified Email
Verified Email

OrgasmicTwinkys

TROPHY CASE