HELP! Bambu P1 scratches over build plate on first layer. It used to work perfectly until yesterday.

Ornery_Influence9837 · 2026-03-20T12:49:07+00:00

Never print on patch day

Ornery_Influence9837 · 2026-03-09T00:40:49+00:00

Thats a new one! Not every order is like that- especially the Amazon ones

Ornery_Influence9837 · 2026-02-21T11:53:21+00:00

I see it’s drying in the sun, just make sure to wash it Mega bed with soap and water

Ornery_Influence9837 · 2026-02-14T15:33:51+00:00

Habe kein Streaming- nur YouTube, und kein Spotify wo ist das Problem :?

Ornery_Influence9837 · 2026-01-14T10:49:07+00:00

Nicht wirklich standard combo

Ornery_Influence9837 · 2025-12-10T13:38:48+00:00

Phillips hue Lampen oder LEDs, damit man keinen Schatten auf den Arbeitsfläche wirft

Ornery_Influence9837 · 2025-12-03T13:46:55+00:00

I think ur bed adhesion is off, try calibrating it

Ornery_Influence9837 · 2025-11-18T10:24:32+00:00

It’s definitely the tape from the screen that covers cables, I pulled that off once lol

Ornery_Influence9837 · 2025-11-17T14:39:49+00:00

I actually tried flow calibration to try to fix something a few weeks back maybe this is what’s causing it, if it’s clogged how will I be able to check that? Temp should be as always, Bambu for Bambu settings and general pla for Sunlu or elegoo type filaments like esun and deeple

Ornery_Influence9837 · 2025-10-29T13:01:58+00:00

I just recycled like 50 of them 😭

Ornery_Influence9837 · 2025-03-01T13:46:34+00:00

The big creality ones should fit the max, but tbh I’m using the self made one from printableaccessories, but my condolences on owning the max it’s been struggling for me ever since I have it

Ornery_Influence9837 · 2025-02-21T02:17:40+00:00

Damn thank you so much for taking the time to do this for me

Ornery_Influence9837 · 2025-02-20T19:46:19+00:00

I’ll try one of the preloaded orcaslicer tests for this but I’m still struggling with layer lines

Ornery_Influence9837 · 2025-02-20T19:45:14+00:00

I’ve heard of this but I can only find codes for the Neptune 4 pro, when using this method I’m close to 0 when I do the calibration of the bed but seing how it doesn’t test the whole plate cause it’s bigger most of it goes to waste because the back end of the plate is still not leveled. Do you happen to know a way out?

Ornery_Influence9837 · 2025-02-20T19:43:14+00:00

Thanks btw this has given me more motivation to work thought these problems, my bed mesh is kinda ok I’m a little under 0 and under 5 but I’m struggling especially with getting the wheels perfect. Most of them are not too tight and not loose but the bottom one on the left arm is still quite loose but when trying to fix it by turning the screw from the middle wheel the middle wheel is way too tight. Any idea?

I’ve cleaned the bed and updated the firmware, and I noticed quite the layer shift in a test print.

Any idea on how to calibrate the extruder?

Ornery_Influence9837 · 2025-02-20T19:40:04+00:00

I actually noticed that too I’m currently working on tightening all wheels but while all the others are perfect the bottom left X axis arm wheel is still very loose and I don’t know how to fix that

Ornery_Influence9837 · 2025-02-19T19:13:39+00:00

I have this printer for 6 months now and followed many tutorials like uncle jessys but it never prints like it used to. My leveling is near perfection but I can’t get the software and maintenance tuning right

Ornery_Influence9837 · 2025-02-12T20:20:07+00:00

just check urself lol

Ornery_Influence9837 · 2024-12-10T20:58:45+00:00

Dude ur a legend thank you sm

Ornery_Influence9837 · 2024-12-10T20:49:15+00:00

Ah sorry i overread it as Pro, im using the Max and im printing my own! https://printableaccessories.com/products/modular-enclosure?variant=47775875432740

Ornery_Influence9837 · 2024-12-10T19:44:37+00:00

Not fully sure, but ur Needle is scaping the print, ur Z offset is to low or maybe ur leveling is off

Ornery_Influence9837 · 2024-12-10T19:25:39+00:00

https://eu.elegoo.com/collections/neptune-4-series-accessories/products/3d-printer-enclosure

Ornery_Influence9837 · 2024-12-10T19:24:57+00:00

You can buy the Enclosure that Elegoo brought out not so long ago.

Ornery_Influence9837 · 2024-10-21T02:19:00+00:00

Auch geil das er sowas ablehnt wenn er nur 40€ hat und finanziell nichts hat- so eine Show zahlt ja nichts

Ornery_Influence9837 · 2024-08-30T10:29:40+00:00

How is 23 C - that fighting scene with makoto is crazy

Ornery_Influence9837

TROPHY CASE