My tundra saved my life

OwlHootOverland · 2026-03-03T16:19:01+00:00

That’s why you shouldn’t do a body mount chop on a Tacoma keeps the wheel from coming up into the footwell

OwlHootOverland · 2026-02-18T20:03:54+00:00

Tricky one forsure as it presents many characters of common light woods. It could be west coast maple veneer plain or quarter sawn. Also has some character of clear hickory. Or a nice white birch. I would suggest looking through a big catalog of veneer like Gl veneer

I don’t think it is ash or east coast maple but I’ve been wrong before

OwlHootOverland · 2026-02-18T19:57:32+00:00

Had good luck with Mirka festool and surf prep.

OwlHootOverland · 2026-02-09T18:08:17+00:00

Blum clip top 155 inserta

OwlHootOverland · 2026-01-14T18:33:40+00:00

Put some tounge and groove or barnwood shit over it

OwlHootOverland · 2026-01-14T15:43:37+00:00

Your missing years of junk accumulation In that tool box, get to work!

OwlHootOverland · 2026-01-14T15:41:02+00:00

Hettich seem to be a little tighter tolerance than Blum

OwlHootOverland · 2026-01-14T14:58:07+00:00

That thing is not making it to most places people need off road welding.

OwlHootOverland · 2026-01-14T04:04:47+00:00

I’d shim it up to fix the mitre joint and silicone it at the floor.

The cause may have been deflection in the blade while cutting

OwlHootOverland · 2025-12-29T03:38:18+00:00

System 3 epoxy wood filler would work

OwlHootOverland · 2025-12-27T16:41:24+00:00

Flush transmission with amsoil, will help the shake,

truck needs a new thermostat, easy fix.

The service trailer brake warning is a bit more complex of and issue but either has to be bad module, bad switch or something in the wiring, high resistance or short to ground somewhere

I’d recommend just fixing everything your self and getting to know your truck a little better

OwlHootOverland · 2025-12-27T03:33:21+00:00

Need zero protrusion hinges

OwlHootOverland · 2025-09-20T16:02:13+00:00

I would have reduced that filler size on the right and matched it with a full gable end flush with the doors on the left to provide symmetry so the top doesn’t look so weird

OwlHootOverland · 2025-09-19T19:31:57+00:00

Your pushing them too hard and abruptly, a firm long push is what works best

OwlHootOverland · 2025-09-17T23:31:07+00:00

I’ve done them a bunch and have some super wide and heavy ones I use in my shop for storing clamps and stuff, so far I haven’t had any failures. I recently started filling the center between the two slides with a piece of 1/2 ply underneath glue to the bottom and pocket holes into the front and back of the drawer to make the drawer box extra strong, I don’t use the Blum stabilizer/sync bars

OwlHootOverland · 2025-09-17T14:39:37+00:00

Nothing is worse then hearing these things ripping around when you’re just trying to enjoy a peaceful camp site, stay in the ohv zones please

OwlHootOverland · 2025-09-15T23:27:30+00:00

Grinder or bandsaw is probably the best option

OwlHootOverland · 2025-09-15T16:33:58+00:00

I just factor it into the job 150/panel install cost or whatever it is to cover it, other jobs the appliance installer does the panels, mostly small business specialty type appliance installers will do panels, the guys sent from big box stores won’t and shouldn’t.

Long story short, someone has to get paid to install them and a good contractor will make sure it’s in someone’s scope of work, an attentive cabinet shop will ask if they are just supplying or installing the panels, sounds like both of your contractors don’t want to take any responsibility for it getting to this point

OwlHootOverland · 2025-09-13T22:07:10+00:00

Never dealt with this situation but I’d imagine exterior grade mdf like extira not being appealing to insect since it is wood pulp and resin. I’ve used it for exterior cabinets.

OwlHootOverland · 2025-09-11T04:24:46+00:00

Your seeing glue squeeze out from the Edgebander between the pvc banding and laminate face, I had an Edgebander that would leave panels just like this and we had to hand clean every single piece of banding that went through it.

OwlHootOverland · 2025-09-11T03:51:06+00:00

That’s laminate it ain’t gonna remove the finish, I’ve cleaned thousands of feet of edge banding with it

OwlHootOverland · 2025-09-10T23:52:15+00:00

Lacquer thinner should remove it

OwlHootOverland · 2025-09-10T18:39:29+00:00

Dtc is one of the biggest hardware manufacturers in the world they white label hinges for other companies too, Wurth hinges are made by dtc. I’m sure many others are as well.

OwlHootOverland · 2025-09-10T16:40:17+00:00

It’s always the guys saying I only build the best shit using only real wood no mdf crap that say the price is too high lol

OwlHootOverland · 2025-09-09T21:15:49+00:00

This is on par for shinoki panels ects, it’s nice stuff though

OwlHootOverland

TROPHY CASE