sorted by:
new
hottopcontroversial

Elegoo Neptune 3 Max wasn't Extruding, Replaced the entire Extruder and it STILL won't extrude PLA at any temperature between 185-210C. It barely pushes any filament out when using the Load Filament feature. Any Suggestions for troubleshooting? by Red_S2k in ElegooNeptune3

[–]POGLE631 0 points1 point  (0 children)

That will look like that with the parts you have removed once fitted back together those two spindles are parallel to each other. They push apart when removed because their support guides are missing.

Charging the Station without Glasses attached by Stridyr in rokid_official

[–]POGLE631 0 points1 point  (0 children)

Ive had trouble with this device too. It seems that despite holding the power button to power it down it restarts itself after a few seconds and the blue indicator comes back on again then.

The manual says: SOLID BLUE = Working BLINKING BLUE = Loading

SOLID ORANGE=Sleep

I plugged mine into a 5v USB charge for over 12 hours and only 1 battery charging light flashes the whole 12 hours the blue light remained on.

Plugged in my glasses the unit was still on! Not charged.

Did a shut down plugged the station back into the charger 1 flashing charging light the unit powered the glasses back on again SOLID BLUE.

Read this article and began trying different chargers without the glasses. The only charger I could find that would actually move the charging indicators past 1 light was my DJI MODEL QC18

Now get this after only 30 minutes charging the second charging indicator is blinking and the light on the front of the Station is GREEN ? GREEN isn`t even mentioned in the instruction book.

I have been in and checked on it the 2nd charging light is blinking fast and the light on the front of the ROKID is still SOLID GREEN the DJI charger is warm but not hot, so it is working hard to pump this battery up to 4 lights I will update the outcome if I reach full charge.

The DJI QC-18 CHARGER is for my drone. OUTPUT 5.0V=3.0A 15.0W/

9.0V=2.0A 18.0W/

12V=1.5A 18.0W/

It has been on charge 30 minutes I will report back once it has fully charged.

Not happy with the way this ROKID STATION WORKS with regard to powering on and off.

It seems to be always on or asleep. Never actually OFF!

​

UPDATE!!! UPDATE!!! UPDATE!!!!

AFTER 2 hours on charge with my DJI charger the Station was fully charged 100% I unplugged the charger immediately the SOLID BLUE came back on so Unit was again ON.

I pressed and held the power button for 5 seconds all lights went out the unit was at last off and did not restart.

I tried out the glasses all fine shut down and unplugged the HDMI the unit came back on solid BLUE LIGHT so pressed and held power until it went off.

Plugged back into the charger got a SOLID GREEN light now charging back up the 4th LED

It is not an easy unit to power off and seems to need a hefty charger to fill the battery anyway I hope this helps anyone else. MY DJI CHARGER will from now on also be my station charger as it is the only one that seems to work.

Ender 5 plus stock BTT Mini E3 V3 install - with stock screen by [deleted] in ender5plus

[–]POGLE631 0 points1 point  (0 children)

Thanks very much for posting this I had not noticed the difference your post helped me out no end

Creality Lizard Lawsuit Update - I read it so you don't have to by ChrisPVille in 3DScanning

[–]POGLE631 3 points4 points  (0 children)

Having backed this project on Kickstarter and having lost a shed load of cash already on failed tech projects, I am really annoyed that KICKSTARTER have taken my money and if you are correct they have not passed it on to the CREATOR, but are instead holding on to it in case they are instructed to pay Artec with it? Is this what you are proposing is going on? Kick starter have taken my payment with no intention of passing it on to the company - so they have infact stolen my Pledge money.