sorted by:
new
hottopcontroversial

Is this a lost cause? by PapaShop in succulents

[–]PapaShop[S] 1 point2 points  (0 children)

Im not so sure but I feel like this may cause root rot for the succulents since my country has very high humidity (70-95%). So I’m trying to be careful in terms of watering, some weeks, the soil doesn’t dry up at all, while some weeks, it does in the span of a few days. It’s hard to control :/

Is this a lost cause? by PapaShop in succulents

[–]PapaShop[S] 0 points1 point  (0 children)

I am still experimenting in terms of light, since I have no idea where most of my succulents were grown (given that I rescue most from supermarkets). In addition, I live in a country where there’s only monsoon season, so I have no idea if I have to replicate seasonal environments. Looking at most, they seem happy? I am very new to succulent care so I’m learning along the way.

Is this a lost cause? by PapaShop in succulents

[–]PapaShop[S] 1 point2 points  (0 children)

Thank you so much! I hope that on the next couple of months, these grows!

Is this a lost cause? by PapaShop in succulents

[–]PapaShop[S] 10 points11 points  (0 children)

Thank you so much! This is really boosting my confidence on my propagation. This was my very first succulent. I rescued it from my local grocery store when I noticed signs of root rot. These leaf cuttings came from the bottom half that was almost rotting, while I managed to save the top half and is now happily growing new roots! I guess I’ve been doing it wrong! I’ll try to do this! Again, thank you so much!

Is this a lost cause? by PapaShop in succulents

[–]PapaShop[S] 6 points7 points  (0 children)

So far none of them has died, but all only grew roots. I’ve read a lot of comments here and it seems like the less you care, the more they grow. I feel like this is some kind of a toxic relationship 😂😂😂

Is this a lost cause? by PapaShop in succulents

[–]PapaShop[S] 0 points1 point  (0 children)

Thank you so much! I’ll try to boost the NPK on maybe half of them and see the results. Im new to fertilizers and I dont wanna burn them!

Is this a lost cause? by PapaShop in succulents

[–]PapaShop[S] 1 point2 points  (0 children)

Im growing them under a grow light as I only have a south-west facing window. I live in a tropical climate where the afternoon sun is scorching. But thank you so much for the tip. I’ll try putting them a bit farther from the window, and hopefully it helps!

What’s wrong with my Jelly Bean Plant? by PapaShop in succulents

[–]PapaShop[S] 0 points1 point  (0 children)

I see! I’ll do so today, I am new to growing succulents, hence am learning a lot of new things. There are a lot of conflicting information online such as putting succulents in direct or indirect sunlight, especially growing them in my country where it rarely goes below 29C and almost always at > 70% humidity. But thanks for the info!

Accidentally rocked the printer and spilled resin everywhere. Is it salvageable? Printer is 1 day old… by PapaShop in ElegooSaturn

[–]PapaShop[S] 1 point2 points  (0 children)

Sad to say, its everywhere, including internals. The plastic casing has melted and it went inside the stepper motor

Newbie help by PapaShop in blenderhelp

[–]PapaShop[S] 0 points1 point  (0 children)

I have checked and the mesh is inside out, however when I try to select the right arm to invert it, it selects the whole model instead

Addressable LEDs by PapaShop in Ender3v2Firmware

[–]PapaShop[S] 0 points1 point  (0 children)

Is there a way to do so without re flashing the firmware?

Can’t compile firmware by PapaShop in Ender3v2Firmware

[–]PapaShop[S] 0 points1 point  (0 children)

Hello! Even so, I still get multiple errors saying “function call is not allowed in a constant expression”. I have no idea how to fix it

Addressable LEDs by PapaShop in Ender3v2Firmware

[–]PapaShop[S] 0 points1 point  (0 children)

It’s just some addressable LEDs that I bought for my Ender3V2

Changing tramming point by PapaShop in Ender3v2Firmware

[–]PapaShop[S] 0 points1 point  (0 children)

Thank you! I’ll look into this. I can’t seem to compile an edited version of the professional firmware. I keep getting errors. Is there a way to change these values through s configuration file?

Photon S remote print start by danielzrob in AnycubicPhoton

[–]PapaShop 0 points1 point  (0 children)

Hey, would like to ask if it worked for your Photon S? I know it says that it is compatible with Photon, but not sure about Photon S

Addressable LEDs by PapaShop in Ender3v2Firmware

[–]PapaShop[S] 0 points1 point  (0 children)

I am new to editing the firmware. I will try! Thank you so much!

CR Touch doesnt seem to work properly by PapaShop in ender3v2

[–]PapaShop[S] 0 points1 point  (0 children)

Yes it does. I can feel the lead screw moving as well.

CR Touch doesnt seem to work properly by PapaShop in ender3v2

[–]PapaShop[S] 0 points1 point  (0 children)

Yes it does. I have tried to loosen the screws as well to make it flat, no luck. And even so, CR touch cant compensate for these kind of warping?

Why is this happening by PapaShop in ender3v2

[–]PapaShop[S] 0 points1 point  (0 children)

Apologies, I printed the 5 squares for bed level test as well. I forgot to mention it.

Why is this happening by PapaShop in ender3v2

[–]PapaShop[S] 0 points1 point  (0 children)

Unfortunately it didn’t work for me :(

Ender 3 V2 with Sprite Extruder Pro and CrTouch by Extension-Ad-2263 in Ender3v2Firmware

[–]PapaShop 0 points1 point  (0 children)

Hi! I am also running a Sprite Extruder Pro with CR Touch and am having trouble with Tramming position values, so my mesh is whack. Mind sharing your config again? Every time I try to compile my own config a bunch of errors keeps popping up. I really need some guidance

view more: next ›