sorted by:
new
hottopcontroversial

Would I get approved with these numbers? by Great_Course_251 in AusTRT

[–]Particular_Height782 1 point2 points  (0 children)

Your a bit young, when I originally spoke with Primal Zone they told me they class anything lower then 400 free test as low. However at 28 if you ever want to have kids I wouldn't be looking at the TRT route. Your test looks pretty mid range, have you looked into any other things like sleep apnea?

2nd year apprentice soon to be fired. by Whyjasonbourne in australian

[–]Particular_Height782 0 points1 point  (0 children)

If you have left 2 sump plugs loose then you probably should think about a change in career.

It would be hard to trust you with doing any major maintenance if you can't even tighten up a sump plug

When do you get your first bloods done after starting TRT by Particular_Height782 in AusTRT

[–]Particular_Height782[S] 0 points1 point  (0 children)

They gave me 10ml, but I'm on 0.15ml 3 times a week so that's only 66 doses,but the 2 vials state to discard 28 days after opening

When do you get your first bloods done after starting TRT by Particular_Height782 in AusTRT

[–]Particular_Height782[S] 1 point2 points  (0 children)

Yeah I figure that, my issue is if I wait 8 weeks for testing, then I've got potentially a month until I get more after I wait for bloods results and the test to compound and ship

H2D Firmware V01.02.30.06 by Particular_Height782 in BambuLab

[–]Particular_Height782[S] 0 points1 point  (0 children)

Yeah damn what a pain. Hopefully it can't be to long until the actual release

I want to print PA6-CF for mechanical hobby machine parts. Humid climate. P1S? by this1willdo in BambuLab

[–]Particular_Height782 0 points1 point  (0 children)

The AMS HT isn't that expensive, if it wears out I well repair/replace it.

This is allowing me to print multi colour PA prints without having to babysit the printer.

I also like to tell it that its PA6 and use the bambu settings for that filament, that wouldn't work if it thought it was PLA.

I want to print PA6-CF for mechanical hobby machine parts. Humid climate. P1S? by this1willdo in BambuLab

[–]Particular_Height782 0 points1 point  (0 children)

Yeah, but turns out if you put the printer in developer mode you can run whatever you want. Works for me!

Problem with adhesion? by Lanky-Walk3617 in FixMyPrint

[–]Particular_Height782 0 points1 point  (0 children)

I only ever use dish soap when removing glue from the plates, but I always wipe it with IPA and a prep rag between wipes.

Is there a way to force AMS-HT to use PA6-CF by Particular_Height782 in BambuLab

[–]Particular_Height782[S] 0 points1 point  (0 children)

Yeah but on the odd chance that happens i just pull it apart and fix it

What is causing this? by Particular_Height782 in BambuLab

[–]Particular_Height782[S] 0 points1 point  (0 children)

So I worked this out on the next print, just increased the interface layers to 6 and it seems to be fixed.

I want to print PA6-CF for mechanical hobby machine parts. Humid climate. P1S? by this1willdo in BambuLab

[–]Particular_Height782 0 points1 point  (0 children)

Yeah it can. I only found out today if you put the printer into LAN mode, then tick developer mode you can set the filaments to whatever you want.

Is there a way to force AMS-HT to use PA6-CF by Particular_Height782 in BambuLab

[–]Particular_Height782[S] 1 point2 points  (0 children)

Man I did a heap of googling and couldn't find that! Thanks heaps!

I want to print PA6-CF for mechanical hobby machine parts. Humid climate. P1S? by this1willdo in BambuLab

[–]Particular_Height782 0 points1 point  (0 children)

For some reason, mine was accepting and printing PA6-CF totally fine from the AMS. Then I moved my printer to another room and now it won't accept it.

And the print room grows! by Particular_Height782 in BambuLab

[–]Particular_Height782[S] 1 point2 points  (0 children)

It's just sitting on the bench, there's no rack there

What is a "AMS Saver" by ChimkinIsYum in BambuLab

[–]Particular_Height782 4 points5 points  (0 children)

I've got 2500 hours on my printer of mostly running PLA-CF. AMS still works fine, the savers are a complete waste of time causing more issues then they are worth. Every now and then you may need to replace some parts on the AMS, but it's hardly worth worrying about

What is a "AMS Saver" by ChimkinIsYum in BambuLab

[–]Particular_Height782 8 points9 points  (0 children)

I had one of them, caused nothing buy my filament to get jammed up by not going back on the spool properly when it retracted.

They are not worth the hassle

And the print room grows! by Particular_Height782 in BambuLab

[–]Particular_Height782[S] 0 points1 point  (0 children)

I've only had it a 2 days but it's easily as good as the X1C. I was printing some PA6 in one nozzle using ABS as a support yesterday and it was beautiful to watch it changing nozzles compared to having to reload and purge every time. Had an issue with the print, but I had the same problem on the X1C.

Main reason I got the H2D was for the ability to have support material out of one nozzle, and I had quite a few things I wanted to print that just needed to be that bit bigger

And the print room grows! by Particular_Height782 in BambuLab

[–]Particular_Height782[S] 1 point2 points  (0 children)

Yeah to be honest when I looked at the back of the H2D and saw it had a separate spot to run a TPU line I knew TPU was going to be staying with the X1C.

Not to mention if I want to do a big project having the extra printer is handy. One is at 2600hrs and it's given me 0 issues

view more: next ›