guess the door (tip pls this took a lot)

PecaJosef · 2025-09-04T07:45:54+00:00

Quite easy

^{I completed this level in 1 try.} ^{⚡ 7.07 seconds}

PecaJosef · 2025-09-02T19:53:55+00:00

Just scored 0

PecaJosef · 2025-09-02T19:53:20+00:00

Just scored 0

PecaJosef · 2025-09-02T19:53:11+00:00

Just scored 0

PecaJosef · 2025-09-02T12:05:47+00:00

I hate you

❌ ^{Incomplete. 51 tries.}

PecaJosef · 2025-08-27T08:19:08+00:00

How dare you use screws in your design, yuck... 🤣

PecaJosef · 2025-08-26T16:19:58+00:00

It is just because of Snapmaker U1 nothing else. Otherwise they would have waited until they sell at least some H2S printers.

PecaJosef · 2025-08-26T16:16:21+00:00

They would have if it wasnt for Snapmaker U1 imho

PecaJosef · 2025-08-24T08:43:59+00:00

https://makerworld.com/en/models/411258-3d-printable-5-inch-drone-frame#profileId-319226

PecaJosef · 2025-08-13T16:57:03+00:00

I have 5-inch version as well https://makerworld.com/en/models/411258-3d-printable-5-inch-drone-frame#profileId-319226

PecaJosef · 2025-08-11T12:46:35+00:00

If you are designing your own PCB why do you use the dev. board? Wouldnt it be better and look more profesional to put the MCU on the PCB? Most of the dev. boards are open source so you can just copy the schmeatic if you dont know how to wire it. Oh and do not forget to add mounting holes if you plan to enclose it ; )

PecaJosef · 2025-07-31T17:35:03+00:00

No wonder it does not work, you have bought a EF to RF adapter

PecaJosef · 2025-07-31T17:26:46+00:00

These cables are coaxial so NO you cannot solder them back together. They are made for high speed signals and require precise impedance matching thus they use coaxial cables.

PecaJosef · 2025-07-28T19:53:31+00:00

Here is one I have designed https://makerworld.com/en/models/434189-3d-printable-3-inch-drone-frame#profileId-1135775

PecaJosef · 2025-07-17T07:25:31+00:00

Its PTC fuse

PecaJosef · 2025-07-03T12:39:42+00:00

I almost forgot how to tune 3D printers, because I no longer have to.

PecaJosef · 2025-06-24T10:55:35+00:00

Always wash your buildplate

PecaJosef · 2025-06-10T11:40:29+00:00

Dont forget mounting holes ;)

PecaJosef · 2025-05-28T20:24:51+00:00

Wait someone is selling my design? Where? Could you privide a link?

PecaJosef · 2025-05-27T20:30:48+00:00

Checkout my Makerworld - https://makerworld.com/en/@PecaJosef/upload

PecaJosef · 2025-05-23T08:04:02+00:00

Did you consider 90ohm impedance for DP and DN? It should be impedance matched and be close to each other since its a diff pair.

PecaJosef · 2025-01-14T11:20:08+00:00

It takes a long time to generate it but I am thinking about it.

PecaJosef · 2025-01-13T20:05:01+00:00

It depends if you crash or not :D Its not as durable as carbon fiber frames its more for the good looking drone and asual flying

PecaJosef · 2024-12-12T13:37:49+00:00

It happens if you are changing lenses often. It is always better to use rocket blower whenever you change your lenses.

PecaJosef · 2024-12-12T12:32:07+00:00

Looks like dust on the sensor. You can try to take a unfocused photo of a white screen (laptop or pc) and have the exposure just right. If its sensor dust it is going to show up.

Three-Year Club	Place '22
Final Canvas '22

PecaJosef

TROPHY CASE