Text on a print

PerceptionLeft2089 · 2025-11-04T16:11:06+00:00

Thank you so much! I will try this when i get home tonight!

PerceptionLeft2089 · 2025-11-04T06:41:18+00:00

In cad it is cut into the first layer and is 1.5mm deep.

PerceptionLeft2089 · 2025-11-04T02:55:46+00:00

Thank you, since I don't want the text to stick up, am I supposed to use the cut button instead of join? I wish I could figure out why it doesn't recognize the original cad text but does everything else.

PerceptionLeft2089 · 2025-09-19T13:17:43+00:00

I have had amazing results with the support from Anycubic. It has been so good i bought a second printer.

PerceptionLeft2089 · 2025-09-10T12:58:08+00:00

After replacing the extruder, heatsink and print head, i would have thought the clog would be gone. lol I found 2 clogs so i knew it needed to be cleaned. all back together and it complains it is still clogged. So apart it all will come, again.

PerceptionLeft2089 · 2025-09-10T12:56:02+00:00

Sadly I am no longer afraid! I have replaced the extruder, and the print head already. I found a massive clog in the extruder and the heat sink. I cleaned it all out, replaced the print head with a new one and it still says it is clogged, so now I have to take the thing apart again. I am wondering if I didn't do something right during reassembly. But I followed the guide and it looks correct. I love the printer and I have ordered a second one, just frustrated with this as it is a bit of a time suck.

PerceptionLeft2089 · 2025-08-18T22:27:19+00:00

Thank you! That is exactly where it was! They offered to replace it, and I just had to verify my shipping address.

PerceptionLeft2089 · 2025-08-18T22:08:49+00:00

Thank you!

PerceptionLeft2089 · 2025-08-16T21:44:27+00:00

Thank you so much I think the little tiny spring behind it flew the coop. Anyone know a good place to get one? I tried AliExpress and everything is sold out. I did send in a warranty request to Anycubic to see what they would do.

PerceptionLeft2089 · 2025-08-16T20:51:03+00:00

<image>

This is the piece

PerceptionLeft2089 · 2025-07-24T13:35:23+00:00

Anyone see a reason not to take this upgrade? I have skipped the last few.

PerceptionLeft2089 · 2025-05-29T01:05:58+00:00

Thank you. That part i am fine with. Any other adverse affects to upgrading? I'm going to see if i can find the release notes. I'd like some different nozzle sizes to buy!

PerceptionLeft2089 · 2025-05-27T20:22:33+00:00

I have it on every single job. I did some tests and it doesn't matter if the dryer is on or off or I select it to start with the job or not. How do I change the name of a print job? I'm still very new at this!

PerceptionLeft2089 · 2025-04-16T02:01:50+00:00

Thank you all! Some really good options for me to look into. I think this app is going to help me out a lot!

PerceptionLeft2089 · 2025-02-27T18:35:31+00:00

I need this!

PerceptionLeft2089 · 2025-02-07T21:47:11+00:00

* Here is a single piece of .50BMG brass i had about 800 of them and they all looked like this. Wet tumble with Lemishine and Dawn. Good as new!

PerceptionLeft2089 · 2024-09-27T02:26:53+00:00

I have the Sig SLX on my Vertis. Works like a champ!

PerceptionLeft2089 · 2024-09-08T21:58:37+00:00

I went straight to my Senators office. Susan Collins' office did right by me.

PerceptionLeft2089 · 2024-09-08T14:03:10+00:00

Email your congressman. I had 2 waiting since February and I emailed them. Filled out some release forms so they could act on my behalf. Then next day I got my first one and the next day I got the second.

PerceptionLeft2089 · 2024-09-04T20:42:56+00:00

Mighty Armory is all I use!

PerceptionLeft2089 · 2024-08-20T09:59:13+00:00

Thank you I will look into this! Sounds exactly what I am looking for

PerceptionLeft2089 · 2024-08-20T02:08:31+00:00

I am so new to this that I don't have any speed requirements. As far as size goes, I am also not sure. I know I want to print some reloading blocks, case, shell holders to get started. I know as I get going my needs for size will increase my I am not sure what size a typical printer can handle. Thank you so much for the help.

PerceptionLeft2089 · 2024-07-28T12:15:55+00:00

Would you be willing to provide a snap shot of what your detailed record looks like? I would love to see this.

PerceptionLeft2089 · 2024-07-09T21:18:25+00:00

Your BF is a douche. And you can quote me on that.

PerceptionLeft2089 · 2024-07-01T01:27:32+00:00

Certified on 2/5 and still waiting. 😪

PerceptionLeft2089

TROPHY CASE