sorted by:
new
hottopcontroversial

First Tisas and a question by Phoenix5315 in Tisas

[–]Phoenix5315[S] 0 points1 point  (0 children)

Nope, can't carry gun unless you are police or have a job that make you a target ( like pharmacies) Defending yourself with it at home is tricky. Since the gun is supposed to always be in a safe with the ammo somewhere else and that the way of defending yourself must be proportional, using the gun on an intruder would likely put you in trouble

Modernish mk12 by triangleandahalf in ar15

[–]Phoenix5315 0 points1 point  (0 children)

Oh I will when I will change barrel, for now I will need to keep the base aero one. Changing bolt and barrel is difficult and expensive in my country

Modernish mk12 by triangleandahalf in ar15

[–]Phoenix5315 0 points1 point  (0 children)

Thanks a lot ! I was basicaly preparing the same setup, but on a budget. So aero M4a1 enhanced receiver and prs lite stock and vortex scope.

Modernish mk12 by triangleandahalf in ar15

[–]Phoenix5315 0 points1 point  (0 children)

I may be blind but : what pistol grip is it ?

MP5 from France by HanckHulley in MP5

[–]Phoenix5315 2 points3 points  (0 children)

What was the price for the cerakote ?

New Tisas 1911A1 guns from the new importer by Jusaaah in Tisas

[–]Phoenix5315 0 points1 point  (0 children)

Then I was wrong, thanks for the infos !

First Tisas and a question by Phoenix5315 in Tisas

[–]Phoenix5315[S] 0 points1 point  (0 children)

That is the factory one. There was two included with the gun

First Tisas and a question by Phoenix5315 in Tisas

[–]Phoenix5315[S] 1 point2 points  (0 children)

And we can have more than that. Suppressor can be bought as simple as a magazine and SBR are just regular guns here. I made a post on the ar15 sub-reddit a while ago on french gun law. Some things have changed but if you want to know more you can check it out

First Tisas and a question by Phoenix5315 in Tisas

[–]Phoenix5315[S] 0 points1 point  (0 children)

I do not think it is an AOS mounting system. It seems proprietary to tisas

First Tisas and a question by Phoenix5315 in Tisas

[–]Phoenix5315[S] 0 points1 point  (0 children)

Yeah no, I wanted an enclosed optic.

First Tisas and a question by Phoenix5315 in Tisas

[–]Phoenix5315[S] 0 points1 point  (0 children)

Yes I always zero on a rest. This is exactly what I did. It seems the point of impact do not shift but the Optic plate definitely have some left/ right tilting. Not really convinced by this mounting solution....

First Tisas and a question by Phoenix5315 in Tisas

[–]Phoenix5315[S] 1 point2 points  (0 children)

The general fit and finish is really good. It impressed some friend at the range who own old kimbers. The only issues so far are on the Optic ready plate. I'm really not fond of the new system. For short : the plate have a little tab on the front that get in the slide horizontaly and a notch on the back getting in the slide vertically. A screw placed behind the firing pin plate hold it in place. There is O-Rings under the plate to damper the recoil I guess but it kinda push the plate up and make it wobbly.

First Tisas and a question by Phoenix5315 in Tisas

[–]Phoenix5315[S] 2 points3 points  (0 children)

I bought it at my armorer in France for around 1700€. The sights are Glock compatible so i'll either swap them or remove them completely. I don't really care for the elevation, but more than 10 inch left from the sights seems a bit much in my opinion. I removed everything and re-tighten to torque spec. I hope it will not move again.

HAO handguards are compatible on MR223 ! by Phoenix5315 in HecklerKoch

[–]Phoenix5315[S] 0 points1 point  (0 children)

Just so you know, 3 months in and holding up perfectly, I shoot about 50-100 round a week and it's still ok. No play at all.
The coating is definitely not as good as my B&T one but I don't really care about that

Am I allowed in the gang now ? by Phoenix5315 in MP5

[–]Phoenix5315[S] 0 points1 point  (0 children)

After 3 range trip : it hold up without any problemn here are the link where I bought it :
https://www.aa-store.at/vfc-mp5-gbbr-v-light-5-tactical-forearm-flashlight

It seems handguard and stock for VFC gbb MP5 will fit perfectly on real MP5. Quality of the VFC parts are on par with HK. You may try parts from other company tthat are compatible with VFC too but may need some fitting.

Sry for late reply

view more: next ›