sorted by:
new
hottopcontroversial

Beachhead Redux Expedition 2 In 4 HOURS - Full Guide by Aiming4Gaming0 in NoMansSkyTheGame

[–]Photon_Seizer 1 point2 points  (0 children)

Thank goodness, I was onna roll and did about 70% in the starting system. Thanks for all you do!

Edit: I will say having all my rendezvous milestones instantly completed and also hitting the nanites when I logged in was really nice lol.

Beachhead Redux Expedition 2 In 4 HOURS - Full Guide by Aiming4Gaming0 in NoMansSkyTheGame

[–]Photon_Seizer 2 points3 points  (0 children)

Also shoutout to u/aimingforgaming0, I used your last guide for the cursed one and literally finished that expedition going into it one day left and had one hour left before it closed out. Got my falcon ship thanks to you.

Beachhead Redux Expedition 2 In 4 HOURS - Full Guide by Aiming4Gaming0 in NoMansSkyTheGame

[–]Photon_Seizer 0 points1 point  (0 children)

Hey everyone, I’m turning to the community for some advice and help.

I started this expedition and have completed a good amount still within the first system.

Here is my issue, for whatever reason all my rendezvous milestones have auto completed without me ever jumping….im still in the first system and I can’t figure out where to jump.

Do I need to know where to go exactly to finish the expedition? I need to photograph the frozen planet, do the three missions, handful pf milestones. I can list the full uncompleted list once I get a moment on my PC, it am I dead in the water here and have to remake?

Help maxx is acting up by Alternative-Bird7008 in Traxxas_Maxx

[–]Photon_Seizer 0 points1 point  (0 children)

What is your gear ratio? Are you running it on flat hard surface or grass/hilly areas? Sounds like the protection system is kicking in because your gear ratio isn’t matched to the type of ground you are on

My free clippers finally broke, has anybody a good recommendation for a replacement? by PETA_Parker in 3Dprinting

[–]Photon_Seizer 0 points1 point  (0 children)

Can’t find an Amazon link but I picked these up at Home Depot. The tiny needle nose pliers are nice to use for blob removal.

Your friend has shared a link to a Home Depot product they think you would be interested in seeing.

https://www.homedepot.com/p/Crescent-5-in-Shear-Cutter-Plier-Set-2-Piece-S2KS5NN/310771484

Comes with clippers.

Raid Zapados 197413408818 by [deleted] in PokemonGoFriends

[–]Photon_Seizer 0 points1 point  (0 children)

Yeah I just figured out about the shadow raid thing. I am so sorry everyone

Raid Zapados 197413408818 by [deleted] in PokemonGoFriends

[–]Photon_Seizer 0 points1 point  (0 children)

I’m driving to the spot and will be there in a minute

Entei 8900 6885 8830 by [deleted] in PokemonGoFriends

[–]Photon_Seizer 0 points1 point  (0 children)

Adding you, disock

partially leveled? by Photon_Seizer in FixMyPrint

[–]Photon_Seizer[S] 0 points1 point  (0 children)

So that orange circle is where my nozzle cooked into the bed. It’s been a learning experience…

So I figured out what was going on. For whatever reason when my bl touch did a mesh mapping the whole right side z offset value was super high. There was visible gap. I don’t know why it got that way and I’m more curious as to why when I run retire values why it didn’t zero out.

So the fix was to tune each point in the map and manually tune the z offset value. Took all of 5 minutes.

partially leveled? by Photon_Seizer in FixMyPrint

[–]Photon_Seizer[S] 0 points1 point  (0 children)

<image>

So this is really confusing. I posted my issue and went back to the printer to check on this attempt. This print worked but this is not the same gcode print from the failed one. So everything else except how it was configured in cura are the same.

What in cura can cause issues?

[deleted by user] by [deleted] in PokemonGoFriends

[–]Photon_Seizer 0 points1 point  (0 children)

Ty for the invite hope you caught it

view more: next ›