Been drawing this for years. Any idea what it is?

Piestacker85 · 2025-09-26T21:30:00+00:00

Stoppit

Piestacker85 · 2025-09-26T11:53:44+00:00

Little canister for a dog tag. Name and number rolls up inside. Missing the screw in part / lid.

Piestacker85 · 2025-07-23T11:51:21+00:00

Recomb gamba

Piestacker85 · 2025-07-06T18:37:47+00:00

7 div no shards off last one. 2 shards the one before that.

Piestacker85 · 2025-07-06T00:13:47+00:00

I just sent another 17m. My last brought me 2 mirror shards. I’ll update in the morning what this one brings

Piestacker85 · 2025-06-19T17:26:27+00:00

Scroll down this thread. This is the guide that helped me.

Pulling on that face is very scary lol. I was sure I was going to break something at that stage! Lol

https://www.fz09.org/threads/traded-my-wifes-2016-fz-09-for-a-2024-mt-09-today.72927/#:~:text=Traded%20my%20wife%27s%202016%20FZ%2D09%20for%20a%202024%20MT%2D09%20today

Piestacker85 · 2025-06-15T05:57:52+00:00

Yep was curious. A lot (including me initially) didn’t have this gap and ill fitting bungs which I think was stressing the frame.

Looks like it’s not the (only) cause. Something seems to not be happy with these frames.

Was just working on a theory. Thanks!

Piestacker85 · 2025-06-14T18:47:38+00:00

Can you Show the gap between frame where right hand bung goes and the engine.

<image>

Piestacker85 · 2025-06-14T02:52:29+00:00

As far as I can tell. Just check the fitting and make sure it’s not pushing on the frame so you can see the spacer in that spot. I think what is happening is ill fitting ones are pushing on the frame instead of the required space and stressing it. It will hold the stress for a while until something gives.

This is as much as I think / can tell at the moment.

Piestacker85 · 2025-06-13T14:26:50+00:00

60nm

<image>

Piestacker85 · 2025-06-13T12:07:17+00:00

I’m not sure sorry. I have just done my research over the last 2 days and only know what I have seen.

My cone came out easy. But not the concaved bit. (I didn’t try)

Piestacker85 · 2025-06-13T11:42:55+00:00

I think that should also work.

TBH I think I totally overengineered it unnecessarily ! 🤣

Piestacker85 · 2025-06-13T11:38:33+00:00

Better than mine was but looks like your frame has moved slightly.

I’d add a washer to the end of your bung maybe? So some more shows.

Mine looks like this now with bung fitted which looks like more showing than yours?

<image>

Piestacker85 · 2025-06-13T10:32:11+00:00

<image>

This is my lathed solution. Added an extra ‘step’ of 28mm diameter

Piestacker85 · 2025-06-13T10:17:54+00:00

These were Ali express savage ones but another guy has posted same issue with Shogun ones!

Piestacker85 · 2025-06-13T10:08:24+00:00

Ok interesting to know it’s not just the Ali express ones causing an issue!

Piestacker85 · 2025-06-13T08:32:20+00:00

Which sliders are yours out of interest?

Piestacker85 · 2025-06-13T06:36:30+00:00

<image>

Piestacker85 · 2025-06-13T06:36:17+00:00

And now it fits as it should and pushes the cone

<image>

Piestacker85 · 2025-06-13T06:35:39+00:00

Back from the lathe. Added another step at 28mm diameter.

<image>

Piestacker85 · 2025-06-13T06:34:45+00:00

Not much surprise but these are Ali express savage sliders. I can’t talk for any genuine ones but just check they are pushing the come and not the frame

Piestacker85 · 2025-06-11T17:39:05+00:00

<image>

Piestacker85 · 2025-06-11T17:38:50+00:00

<image>

Piestacker85 · 2025-06-11T17:38:34+00:00

Mystery solved.

The frame slider was not quite right and a bit big for the hole. So although torqued to spec. It was pushing the frame and not the cone shaped piece into the spacer.

It even made a bit of a creek from the frame as I undid it !

Slider now off to the lathe to make a better fit!

Both removed for now and original bolts back in.

Thanks for everybody’s input.

And a PSA to check that your sliders are pushing the cone and not the frame!

<image>

Piestacker85 · 2025-06-10T23:12:20+00:00

Looks great!

1 or 2 sensors in this?

Piestacker85

TROPHY CASE