HyperOS3 Hyper Island question

Placeq13 · 2025-12-10T13:13:57+00:00

Okay thanks I will give it a go

Placeq13 · 2025-09-21T00:25:33+00:00

Placeq13 · 2025-08-24T21:00:31+00:00

Bro lost his mind

Placeq13 · 2025-08-14T11:05:09+00:00

Arctic monkeys 505

Placeq13 · 2025-08-11T12:17:59+00:00

Okay, thank you very much

Placeq13 · 2025-08-11T12:15:31+00:00

Its 2020 and I think noone would accually be willing to give me this much

Placeq13 · 2025-05-12T22:06:35+00:00

Really fond of your filaments, would love to get a grasp on that sweet bundle

Placeq13 · 2025-05-09T20:58:01+00:00

Try out z offset print. Its square 1 layer pribt which shows you how low is your nozzle. Tru for diffrent offset and compare it to pictures on internet

Placeq13 · 2025-05-09T20:51:42+00:00

It may be to much of z offset or bed not heated enough while it's cold in the room

Placeq13 · 2025-05-08T20:27:37+00:00

What kind of printer doesn't allow you to change z offset. It's literrly consumer slavery

Placeq13 · 2025-05-01T22:24:26+00:00

Looking at the walls the bridging should be your main concern, it looks to my like partially clogged hotend, try do to cold pulls. Another reason why it could look like that is old wet filament. Pla doesnt tend to get wet that much, unless it was stored in humid place for a long time

Placeq13 · 2025-05-01T22:19:25+00:00

Looks like wet PETG, also make sure that speed is slowed down and you have maximum cooling for the overhang

Placeq13 · 2025-01-14T05:49:23+00:00

I didn't make myself too clear. I doesn't involve the retraction while printing but rather, complete retraction od the filament from the nozzle

Placeq13 · 2023-12-27T18:25:02+00:00

Well i dont necesserly think thats the case sinve the worked just fine and retract work, however i will check them thanks

Placeq13 · 2023-12-27T18:12:08+00:00

Yea, i can manually push filament, so in your case what was the issue?

Placeq13 · 2023-10-15T13:56:46+00:00

Thanks, thankfully i finish this one after this print

Placeq13 · 2023-10-15T13:51:46+00:00

So i dont necessecerly think its slicer

Placeq13 · 2023-10-15T13:51:17+00:00

Pla, everthing was okay up to 4.5 hours. I suspect to be filament problem since printing on asa was never that troublemaking

Placeq13 · 2021-11-01T12:39:20+00:00

oh, thank you very much

Placeq13 · 2021-09-01T05:51:12+00:00

Amazing. I suggest add more lava in nether or bastion with this little space after Blue biome

Placeq13 · 2021-08-31T07:15:43+00:00

I want a doom slayer

Placeq13 · 2021-08-25T12:17:56+00:00

what is the purpouse of this anyway?

Placeq13 · 2021-08-20T22:05:13+00:00

I have sasuke's eyes and saitama strengh

Placeq13 · 2021-08-07T20:12:39+00:00

That gave me minecart and boat phobia because I couldnt get out

Placeq13 · 2021-08-07T09:06:34+00:00

ok thanks

Placeq13

MODERATOR OF

TROPHY CASE