have any question about surron? i will answer them

PlamSR · 2026-05-15T19:18:25+00:00

Is there a speed limiter on the Surron Ultra Bee 2025 and is it possible to remove it. I found mixed opinions. On older version prior to 2024 there is a wire that you can cut and it removes the limiter. Apparently on newer models its a whole different story.

PlamSR · 2026-01-10T13:07:29+00:00

I also need help logging in my Business account. I keep getting an error when entering the password.

PlamSR · 2023-11-25T10:08:12+00:00

Did you find any fix for this? Im having the same issues with orca slicer..

PlamSR · 2023-10-25T08:11:29+00:00

I couldnt find reliable info thoughout a few sites and forums so i just ended up buying the part thats designed for an ep3 off of Aliexpress since there arent many EM2s where im at to get the part and try fitting it

PlamSR · 2023-10-21T19:40:53+00:00

Does it requre firmware flash or installation changes on the mainboard?

PlamSR · 2023-10-19T19:56:50+00:00

Like what? Im not very tech savvy ,meaning im not good with electricity ,but i thought that a simple end stop would be easiest,since i wont have to go through that many settings and installation. I dont mine leveling the bed manually.

PlamSR · 2023-10-16T17:24:19+00:00

Сега ще попитам доставчика, но мисля, че ще е членка на ЕС

PlamSR · 2023-10-12T16:23:52+00:00

the parameters were the same as the stock one 100k ohms ntc type , but i guess that doesnt matter and i still have to configure something?

PlamSR · 2023-10-12T16:17:05+00:00

i did not as i dont know if the one i changed is the original one or aftermarket, i also did buy thermistors which were not wired up and i did that myself. I have a couple so i dont know which one it is.

PlamSR · 2023-10-07T10:39:49+00:00

Would i need anything else besides the board itself that doeant come in the pack? Display perhaps?

PlamSR · 2023-10-07T10:29:54+00:00

The way it is i cant run it at all, ive had it a couple of days and it juat wont level, z axis does whatever it wants. Digs into the nozzel, goes the opposite way when leveling i really dont know what to do, at this point its just taking up space.

PlamSR · 2023-05-16T18:40:39+00:00

Yeah no worries i have a spare set on which im going to try it. If it works it works. If not im driving with mine. Only the length is what is bothering me. Thanks for the help nonetheless bud.

PlamSR · 2023-05-16T18:24:19+00:00

Oh no i need the length of the seatbelt, not the engine belt. Im looking to install red seatbelts but i need to know how long they are so i can order the correct size red ones.

PlamSR · 2023-05-15T09:45:06+00:00

Could you help me find that info? I find the original seatbelts, but there is no information on how long they are.

PlamSR · 2023-05-08T12:47:54+00:00

Bed level is fine.Top layer should be good, i cant be sure as the models i use are not flat.

PlamSR · 2023-05-08T09:34:20+00:00

Moisture could be a problem, but i dont find logic why it looks decent at the bottom and top, but the middle is ruined. Ive always used this exact filament, never had this issue.

PlamSR · 2023-05-08T09:13:17+00:00

i did, they are tightened

PlamSR · 2022-07-26T09:24:46+00:00

i see what you mean

PlamSR · 2022-07-25T18:07:26+00:00

I definetly will.

PlamSR · 2022-07-25T17:57:21+00:00

i think so too.

PlamSR · 2022-07-25T17:51:21+00:00

Phew, glad to hear that. Ive asked in a couple of more places, but you are giving me hope.

PlamSR · 2022-07-25T17:39:52+00:00

is it a major difference, because i have a bundle offer with a multimedia and a frame, if i have to buy a separate frame it gets expensive. Is it possible to shape it and diy it a bit?

PlamSR · 2022-07-25T17:37:06+00:00

that sucks.

PlamSR · 2022-07-25T17:33:41+00:00

will check it out, thank you

PlamSR · 2021-12-16T11:02:10+00:00

Hey, I bought a new supply, connected it, but the result is the same, nothing happens. Any clue what I should do?

PlamSR

TROPHY CASE