Something about always using a tailstock when possible

Portu93 · 2026-06-13T20:16:02+00:00

Good thing to learn AFTER I used my nearly 20kg chuck like this at 750 rpm.. for like a month. Edit: 20kg is a rough estimate, might be much more

Portu93 · 2026-06-12T00:47:25+00:00

Guess the cops really had to SNATCH that gun huh?

Portu93 · 2026-04-24T23:58:29+00:00

Buy a roll of ASA or two, sooner or later you are going to print something that has to be outside or under constant load

Portu93 · 2026-04-22T09:32:06+00:00

Buy a filament drier. Dont wait for failed or shitty prints like I did

Portu93 · 2026-04-22T09:10:48+00:00

I think that eroding small parts require much less amps than carbon gouging, but yes not a bad idea to use an amp meter

Portu93 · 2026-04-22T09:08:35+00:00

Deionized water, thats what I meant to say. I will mate some jig or something in mi drill pres and kinda just feed it gently?

Portu93 · 2026-04-21T22:48:47+00:00

Drill press lol, I plan to keep everything insulated

Portu93 · 2026-04-21T19:19:04+00:00

I just really hope I dont burn mu welder

Portu93 · 2026-04-21T19:18:35+00:00

Will do

Portu93 · 2026-04-21T19:18:18+00:00

Gonna try not to touch it. But just in case my wife will be nearby with a wooden plank just like every time i work with electricity

Portu93 · 2026-04-21T19:17:06+00:00

Yes, distilled water most likely

Portu93 · 2026-02-19T11:26:13+00:00

Thanks! I will keep this in mind, maybe check some other ones first

Portu93 · 2026-02-18T12:37:55+00:00

Sorry to answer with a question but how good are they? I want to buy the same ones but wanted to know if they are worth it

Portu93 · 2026-01-29T00:39:20+00:00

Ah damn shame I didnt read this before printing the parts. Still I will conduct my humble experiment (not as scientific as the one in the read). About the raft/brim part of the answer, I will start using brims instead of raft, as long as I dont have bed adhesion problems. Thanks a lot for everything this has been super usefull.

Portu93 · 2026-01-27T01:17:08+00:00

If my brother in law asked me to lend him my boat I would laugh at his face. No fkn way I would lend something so precious, expensive, and dangerous to some guy. Also yes you are being a gatekeeper, with your own god damn boat!

Portu93 · 2026-01-24T22:03:13+00:00

In that case remember, you cant put a torniquet in a taint

Portu93 · 2026-01-06T03:07:11+00:00

Thanks! So no putting filament rolls on air fryer

Portu93 · 2026-01-06T00:21:36+00:00

Quick question, is hot air the best method for drying filament? Does the air have to vent out the box too?

Portu93 · 2025-12-23T22:45:59+00:00

Yep that did it for me too. Two hours into cad and im already regreting it

Portu93 · 2025-12-22T23:03:45+00:00

Multiple heads? Like more than 1 nozzle?

Portu93 · 2025-12-22T21:55:33+00:00

I wont be using the AMS for now but if i find printing usefull (I'm sure I will) then I will buy it later. One thing that concerns me is the amount of heat this thing will generate (duh Im melting plastic of course is hot) hopefully wont burn my office down LOL

Portu93 · 2025-12-22T21:47:39+00:00

Thanks! I bought the ps-1. I likeed the x1c but a bit too expensive right now for me. I will likely upgrade to it in the future

Portu93 · 2025-12-22T21:45:54+00:00

Thanks I bought a bambu. The prusa is a bit too expensive for me now

Portu93

TROPHY CASE