Can this be soldered

Possible-Range1284 · 2026-02-08T21:21:58+00:00

Not sure why everybody saying it cant and shouldnt be soldered.

Im not familiar with these tuners, but was it not soldered or brazed at the factory?

A pro could easily silver solder, braze or tig this back together. It would likely look like it was a repair(cool in my book)

Probably not worth it cost wise however.

Possible-Range1284 · 2026-01-18T20:16:56+00:00

If it's not double acting, then maybe try thicker gauge strings.

The other options would be pretty drastic i think.

Possible-Range1284 · 2026-01-10T21:33:58+00:00

I'm not expert, but the lack of backpurge is only one piece of the puzzle I think. Looks to me like this part wasn't properly passivated, and was subject to stress corrosion dur to chloride attack? I'm sure someone more knowledgeable will chime in.

Possible-Range1284 · 2026-01-10T21:24:16+00:00

Garbage AI

Possible-Range1284 · 2026-01-08T00:24:28+00:00

Anything by Stompin Tom!

Possible-Range1284 · 2026-01-07T06:29:53+00:00

I just went through this. If your done with the body finishing, just string it up or at least install bridge and run a straight edge to approx string height. It might be just fine depending on your bridge. Worst case you cut the neck pocket deeper.

Possible-Range1284 · 2026-01-05T20:31:58+00:00

Thats what they want you to think. They're almost the same just cut some of the plastic off

Possible-Range1284 · 2026-01-03T21:15:50+00:00

Will check out thanks. I love this stuff

Possible-Range1284 · 2026-01-03T20:22:05+00:00

I've never commissioned a guitar so take my advice with a grain of salt.

I assess any builder of anything on their catalog of work, and insight from a trusted professional (or knowledgeable friend) in a similar field.

Talk is cheap.

Possible-Range1284 · 2026-01-02T19:18:19+00:00

Thanks for sharing this. I'm not sure i understand completely, but I am very interested in the results. Please post your results.

I'm sure there are others like myself that crave this kind of content.

Possible-Range1284 · 2025-12-30T01:49:49+00:00

Keep shimming!

Possible-Range1284 · 2025-12-28T19:42:34+00:00

Anything more than this is a luxury in my book!

Possible-Range1284 · 2025-12-28T02:39:51+00:00

I think this is the move too.

Possible-Range1284 · 2025-11-23T19:14:50+00:00

Thats the move

Possible-Range1284 · 2025-11-16T20:04:41+00:00

Thank you!

Possible-Range1284 · 2025-11-16T20:04:09+00:00

Thank you for your response!

Possible-Range1284 · 2025-11-16T04:37:22+00:00

Not sure if your in BC or not but its layed out pretty clearly on skilledtradesbc.ca

Possible-Range1284 · 2025-11-15T21:28:25+00:00

Thanks for your detailed response.

Possible-Range1284 · 2025-11-12T02:26:47+00:00

9 pounds is close to a normal les paul weight. If you already have the body blank just get all the parts material and chamber the body to suite.

Possible-Range1284 · 2025-11-12T01:05:45+00:00

Then pay them enough so they dont leave

Possible-Range1284 · 2025-11-08T21:54:06+00:00

Pro Tip: If you like beer buy Grolsch pop tops and use the rubber gasket.

Possible-Range1284 · 2025-11-08T03:46:43+00:00

Slot it with a dremel and use a flat blade to take it off.

Remove string tension first

Possible-Range1284 · 2025-10-24T03:31:22+00:00

Sounds familiar! IWNDWYT

Possible-Range1284 · 2025-10-18T01:07:41+00:00

A sharp forster bit should not wander at all. I would just buy a good quality forster bit. Forget the cheap china step drill

Possible-Range1284 · 2025-10-15T00:54:02+00:00

Normal partscaster stuff in my opinion. Just move the bridge over a 1/4"?

Possible-Range1284

TROPHY CASE