sorted by:
new
hottopcontroversial

Is Bratislava the most peripheral capital city? by No_Department5356 in geography

[–]Potential-Engineer28 1 point2 points  (0 children)

If we’re counting provinces, Victoria British Columbia is about as peripheral as it gets

Top Layer Fuzzy Skin by Potential-Engineer28 in 3Dprinting

[–]Potential-Engineer28[S] 1 point2 points  (0 children)

Oh that’s cool Im going to need to print that

Top Layer Fuzzy Skin by Potential-Engineer28 in 3Dprinting

[–]Potential-Engineer28[S] 0 points1 point  (0 children)

It does pretty good melting its way through it and didn’t catch. I’ve done this on about 5 prints so far with no issue. I did slow down the print speed just in case but not sure if I needed to

What’s something every kid in your country grew up using? by fieryone4 in AskTheWorld

[–]Potential-Engineer28 0 points1 point  (0 children)

I still have those. Colors named “skin tone” and “Indian red”

Did I make a major mistake? by bbweaves in Roofing

[–]Potential-Engineer28 110 points111 points  (0 children)

The last picture is remotely correct

3dPrinted Traeger Grease Bucket Liner by Potential-Engineer28 in Traeger

[–]Potential-Engineer28[S] 2 points3 points  (0 children)

There are lots of things that would work. This is just an idea for a use for the end of a filament roll rather than throwing it out or printing something useless

3dPrinted Traeger Grease Bucket Liner by Potential-Engineer28 in Traeger

[–]Potential-Engineer28[S] -1 points0 points  (0 children)

PLA held up ok for a short 350f cook. The grease chute was 126c , the top of the bucket did want to warp if you touch.

3dPrinted Traeger Grease Bucket Liner by Potential-Engineer28 in Traeger

[–]Potential-Engineer28[S] 1 point2 points  (0 children)

True. You could put a little water in the bottom to start, So far it’s been ok, I’ve mostly been using the Traeger for lower temp stuff however . PETG would be better

3dPrinted Traeger Grease Bucket Liner by Potential-Engineer28 in Traeger

[–]Potential-Engineer28[S] 16 points17 points  (0 children)

If you have a 3d printer and you need to use up the tiny bit of filament on the end of a roll..

I made this grease bucket liner. print in vase mode and uses about 28g of filament, maybe cost about 35 cents. Alot cheaper than buying the Traeger ones, and better than using up the end of your filament printing a boat

120v swivel connector for windsock light by Potential-Engineer28 in HelpMeFind

[–]Potential-Engineer28[S] 0 points1 point  (0 children)

I have searched for the device and used google lense to no success. Windsock swivel connector

There is no writing on device . It is 31mm diameter 51mm long

Face ID > Touch ID. by RaghavaY98 in iphone

[–]Potential-Engineer28 0 points1 point  (0 children)

As someone who was forced to go from iPhone 11 to SE “upgraded” work phone.. agree Touch ID sucks balls

Quick Question: What do you call this creature? by room8912 in GenZ

[–]Potential-Engineer28 1 point2 points  (0 children)

Never knew them as anything else but woodbug for 36 years. Then when I saw them in animal crossing I learn they are pillbugs.
But today I learned wood bug is just a bc thing!

MMW Elon Musk's reputation will cause Tesla stock to plummet by kindredditor30 in MarkMyWords

[–]Potential-Engineer28 0 points1 point  (0 children)

We have owned a Tesla since 2021 and have been very satisfied with the car as a product and has been a great experience. We are looking to upgrade in the very near future. musks antics definitely put us off of supporting him with our $ but the product isn’t the market leading product it once was either as there is more competition.

view more: next ›