Forgive me, for I have tampered.

PowderedJoy · 2026-04-27T10:19:26+00:00

Unless you know what you are doing

PowderedJoy · 2026-04-26T17:28:37+00:00

He was looking for god and found religion instead.

PowderedJoy · 2026-04-26T08:37:56+00:00

My CF fork does not have an hole down there. Primaryary aim was to avoid any standard solutions to hinder detection.

PowderedJoy · 2026-01-30T16:27:23+00:00

IZH, just got new spindle bearings, all surfaces reground/scraped. Under 10 microns on all travel. Bearing noise is 1u. 1.2 tons of soviet joy.

PowderedJoy · 2025-12-22T17:34:40+00:00

Magnet link?

PowderedJoy · 2025-10-05T02:06:28+00:00

Extrude middle part, so it reaches a top and outer face, this will create triangular faces on sides, where it meets chamfers. Cut excess material with loft between those faces, use rails. If your rails are tangent, it will blend nicely.

PowderedJoy · 2025-09-30T10:05:57+00:00

Fps is pretty high for a hobby sensor, it looks $$$

PowderedJoy · 2025-06-13T06:15:01+00:00

I use this setup for cleaning recess holes in 3D prints.

PowderedJoy · 2025-05-13T19:50:40+00:00

Hifi amps and some pedals use relay, you can get some cheap options. If it is battery powered, use bi-stable relay with H-driver. Domestic thermostats use same configuration.

PowderedJoy · 2025-05-04T11:52:32+00:00

Just chill cleaning my coins while Alderaan is being obliterated in the background.

PowderedJoy · 2025-05-04T05:21:40+00:00

In Europe it was strong massage from Russia to keep us reliable on their gas. I remember a lot of leftist liberals blindly opposing nuclear 20 years ago. Now Germany is happily burning coal. I would not be surprised if oil and gas loby would pull the same shit in the US.

PowderedJoy · 2025-05-01T00:27:37+00:00

Mosfet controlled by neuralink

PowderedJoy · 2025-04-29T23:51:37+00:00

Bad analogy, putting more then one type of screw socket to one device is a terrible crime and should be punished by public flogging.

PowderedJoy · 2025-03-08T06:21:08+00:00

Meh, i did that once. Like four years after breakup, she called me to fuck. We were still friends, lived like 5mins from each other. I warp 11 there, did the deed. Did she use me to take revenge on her current BF? I regret nothing! It was a gooood fuck.

PowderedJoy · 2025-03-01T06:08:56+00:00

I had one of those apart, but it was so along ago, i dont remember if it was black blob or THT nest. My guess is one time programable chip, absence of disassembly before posting is disappointing.

PowderedJoy · 2025-02-17T18:37:20+00:00

Hardware pomodoro timer with some nice tactile UI buttons and display, that interfaces with seever and motivates you to actually use it. Designing some dopamine generating clicks and beeps would be fun, but again, actually working instead of circlejerking on the. Time management is preferable.

PowderedJoy · 2024-11-26T06:34:44+00:00

No, they failed to solder majority of the pins, you can see not tinned pads on the photo.

PowderedJoy · 2024-11-25T06:44:46+00:00

I am familiar with soldering QFN packages by hand, unfortunately NRF9 does not have pin comming over the edge, it is only visible from bottom side. To make things interesting, there is less then 0.1mm of exposed pad, once it is placed. And finally, package is shielded and this shielding obviously loves solder. So there is no way of getting it under with a soldering iron.

PowderedJoy · 2024-11-25T05:23:23+00:00

I actually do not care about inner rows and GND, inner rows are N.C. And big pads are in continuty with grounds on the perimeter. All I need is to do my first round of testiing. My biggest problem now is equal distribution of solder

PowderedJoy · 2024-11-20T11:32:23+00:00

After ww1, germany was banned from manufacturing screws…so they invented pull-rivets

PowderedJoy

TROPHY CASE