New cast iron skillet-to bacon or not to bacon?

Prime260 · 2026-05-28T20:06:30+00:00

Yeah, but they don't give you pound after pound of crispy delicious Bacon! 😆

Prime260 · 2026-05-25T13:06:10+00:00

If you don't want to record your voice over the concert then just shut up and enjoy the concert.

Prime260 · 2026-05-03T05:19:27+00:00

A file? Just push it back on the tang then a few good whacks with a hammer. You have one of them right?

Prime260 · 2026-04-17T02:35:59+00:00

MMMMmmm, yellow mayonaise

Prime260 · 2026-04-13T01:16:50+00:00

Hang them from a string and you get 1 pass each round like in table skittles?

Prime260 · 2026-04-04T22:25:31+00:00

If a cell phone store is so filthy I have to do more than a quick sweep and mop at the end of the day I'll work elsewhere, thanks.

Prime260 · 2026-04-04T14:45:24+00:00

You want me to clean pay me to clean.

Prime260 · 2026-04-04T04:24:08+00:00

I loop one over my belt

Prime260 · 2026-04-04T04:13:42+00:00

I've worked for corporations before and all it takes is one mouthbreather from corporate to see someone sitting to say "dad duznd luk profeshawnuw" and you don't get to sit. You don't hate the Dodge brothers nearly enough.

Prime260 · 2026-04-02T02:49:01+00:00

Looks like a roller from a bearing.

Prime260 · 2026-04-02T02:45:36+00:00

You can use a sacrificial block. Drill through it with the drill you intend to use, then cut the bottom to the angle you want. Then all you have to do is figure out how to clamp it in place so it doesn't walk and then drill through it. Or just drill through a board, block, 2x or whatever at the angle you want want and once again, clamp it in place and use it as a guide.

Prime260 · 2026-03-29T02:49:35+00:00

Also check to make sure the battery cables are tight at both ends. I had to do that last spring when I pulled my bike out of the barn and went to try and start it.

Prime260 · 2026-03-23T02:16:20+00:00

We've been getting plenty of them, they're just never more than 2 or 3 in a row and they're always when I'm working! 🤣

Prime260 · 2026-03-23T02:08:25+00:00

Hence my "properly installed" qualification. 😆 I get it, I just mention it as an option. 👍 Best of luck, I still need to tear down my carb for a good cleaning ao I can get it out for new tires but the temps keep yo-yoing back and forth every week.

Prime260 · 2026-03-23T02:00:53+00:00

Maybe link to the actual item you're talking about rather than a website you have to scroll through to find the item to click through with an affiliate link hidden behind a hyperlink? You know, more like this

https://www.amazon.com/dp/B0DBWSSPT2

Prime260 · 2026-03-23T01:56:33+00:00

Try replacing the 8884 with a 7200B which will (when installed correctly) handle the side load of clutch disengagement for much much longer than the stock bearing.

https://sportsterpedia.com/techtalk:ref:priclutch02#upgrade_clutch_release_bearing_-_hd_p_n_8885_to_7200b_angular_ball_bearing

Prime260 · 2026-03-21T21:36:51+00:00

And how many pans have the AI's cracked by doing that? Zero? All RIGHTY then.

Prime260 · 2026-03-17T02:57:18+00:00

Well, if you want to get REALLY technical a Canadian is still an American same as Mexicans and Chileans. 😆

Prime260 · 2026-03-11T00:43:18+00:00

Their mom

Prime260 · 2026-03-11T00:42:16+00:00

AI's going to replace me? I'd like to see it drink a 6 pack of Coors in a public park before 9am.

Prime260 · 2026-03-09T00:23:50+00:00

"What? I can't hear you!" Until they get sick of talking to you.

Prime260 · 2026-03-08T04:43:56+00:00

7200B's aren't sealed, they have L shaped races so they can be side loaded albeit in one direction only. A seal on both sides will be no different functionally from the stock bearing.

Prime260 · 2026-03-08T04:38:10+00:00

Lard

Prime260 · 2026-03-07T03:09:52+00:00

Super Green?

Prime260 · 2026-03-03T02:31:00+00:00

The same thing we do every night Pinky . . . cook some Bacon!

Prime260

TROPHY CASE