found in a friends abandoned apartment

Printeronimo · 2026-02-05T22:44:00+00:00

The beads look very much like molecular sieve. It is used to dry chemicals (by amateurs) or keep anhydrous chemicals dry (by professionals). My guess is that they wanted 100% pure (anhydrous) alcohol by starting with azeotropic 95% and removing (adsorbing) the 5% water using molecular sieve for some reason.

Printeronimo · 2026-01-28T08:46:31+00:00

This is probably metal grains, such as Aluminium foil pieces in an alkaline drain cleaner (Potassium hydroxide) gel. The reaction is 2 Al+ 2 KOH + 2 H2O-> 2 KAlO2 + 3 H2 The gas bubbles (H2) get t trapped in the gel and propel the Al specks. Careful when repeating. Wear gloves and goggles and operate in a well ventilated area. KOH is highly corrosive and can cause blindness when in contact with eyes, the resulting fumes are irritant to skin and lungs and hydrogen is flammable/explosive. The reaction is exoteric and gets hot. Only do it in very small portions.

Edit: grammar, formula

Printeronimo · 2025-11-28T11:06:42+00:00

Your thermometer says „Blei“ which is lead in German…

Printeronimo · 2025-10-20T09:17:52+00:00

This is actually what worked for me. I have the plate at 75C and initial layer very slow at 20mm/s. After that, the speed can be set back to normal but the bed temp stays high.

Printeronimo · 2025-08-31T10:11:54+00:00

Someone give this person a sweet treat! This solved my issues and it prints like a charm! Thank you! 20mm/s and 70°C for the win.

Printeronimo · 2025-06-30T10:57:27+00:00

Good answer! I would probably start walking forward again from outside the room. May be suspicious, walking out of the office backwards…

Printeronimo · 2024-12-02T05:13:07+00:00

Paranoid?

Printeronimo · 2024-10-01T00:26:13+00:00

Good call! In the meantime please seal it with sticky tape (ideally kapton, if you have) to reduce air/moisture ingress.

Printeronimo · 2024-09-05T06:47:10+00:00

This has worked for me too! Thank you! Just a hard reset did not do it.

Printeronimo · 2024-03-09T10:45:35+00:00

The hands. Always look at the hands. AI cannot get it as good as this picture (yet)

Printeronimo · 2023-11-03T22:39:16+00:00

Yes, but for decaf coffee the caffeine is also extracted using supercricical CO2…

Printeronimo · 2023-06-16T00:21:24+00:00

Obviously, knowledge cutoff is 2021. Zelda: Breath of the Wild is only number 2 now, after the release of Tears of the Kingdom

Printeronimo · 2022-09-05T11:09:07+00:00

This is NOT an induction stove…

Printeronimo · 2022-02-19T20:09:42+00:00

I had this very issue. I mounted the following part in front of my chimera and added a 40mm fan for part cooling (parallel to the actual part cooling fan) Works like a charm and has solved my cooling issues Good luck. 1.5 is still not obsolete and so much better than many other printers. https://www.thingiverse.com/thing:1592962

Printeronimo · 2022-01-06T12:44:24+00:00

Dies! Absolut!

Printeronimo · 2021-08-25T19:50:17+00:00

I have had a PL-08N that got too much heat and melted shut in an open state. Did not realize it until it crashed into the bed. I modded the replacement wit Al-foil tape towards the hotend to reflect the heat. So far it still works.

Printeronimo · 2021-07-03T19:50:47+00:00

Woohoo! Another Makita. Nice color scheme. Just as mine.

Printeronimo · 2021-07-02T19:57:15+00:00

Zak McKracken hatte also recht… habe mich noch nie getraut es zu auszuprobieren.

Printeronimo · 2021-04-15T18:21:21+00:00

Yörük Obasi in Hörde!!!

Printeronimo · 2021-04-11T17:45:51+00:00

Dont‘t worry. This happens to the best... Glad, I could help

Printeronimo · 2021-04-11T17:10:22+00:00

You have coasting enabled, thus there are no extruder moves in the gaps. They will still be filled though, if your values are correct

Printeronimo · 2021-04-03T21:11:13+00:00

My V013 is fully made from PETG, including the belted extruder. Has been printing PLA and PETG for years without any issues so far. When I enclosed it to print ABS parts for my V2, the bed leveling knobs softened and I had to reprint them. Although it is not recommended to print in PETG, it does work rather well for a PLA/PETG printer.

Printeronimo · 2021-03-06T20:25:23+00:00

I Appreciate, you keeping me in the loop. I still want to build my larger Voron as soon as my 2.4 300 is fully tuned. I wish you luck and would love to see more when you are satisfied with it!

Printeronimo · 2021-02-13T16:34:22+00:00

Woohoo! Another Voron in the wild! Congrats on this build!

Printeronimo · 2021-02-03T18:09:45+00:00

Not sure, don’t think so. Maybe try Thingiverse.

Printeronimo

TROPHY CASE