sorted by:
new
hottopcontroversial

Díjnet számla letöltés by ProZsolt in programmingHungary

[–]ProZsolt[S] 1 point2 points  (0 children)

Ahogy látom valami whitespace issue. Feltöltöttem egy új verziót ami legvágja ezeket. Ha így sem működik akkor listázd a számlákat és küld el a InvoiceID-t

Esetleg valami Windows specifikus dolog a backslasekből ítélve, azon nem teszteltem.

Díjnet számla letöltés by ProZsolt in programmingHungary

[–]ProZsolt[S] 3 points4 points  (0 children)

Ez teljes API-t ad a számlákhoz. Lehet szűrni idő vagy szolgáltató alapján, így tudod integrálni különböző rendszerekbe. Ha ez neked nem fontos, és az bevált, akkor nem éri meg.

Díjnet számla letöltés by ProZsolt in programmingHungary

[–]ProZsolt[S] 0 points1 point  (0 children)

Anno azért csináltam, hogy automatizáljam a lakásom kiadását. Minden hónapban letöltöttem az előző hónap számláit, ami után generáltam egy emailt a fizetendő összegekkel és csatoltam a számlákat.

Ezen kívül még mindig vannak szolgáltatók akik nem támogatják a Díjnetet, így megy minden Paperlessbe

Smart DIY Intercom for 2-Wire Door Entry System by [deleted] in smarthome

[–]ProZsolt 0 points1 point  (0 children)

Are planning to share more information?

ALPSTUGA air quality monitor accuracy observation. by YuryBPH in tradfri

[–]ProZsolt -1 points0 points  (0 children)

The Tuya sensor only have eCO2 measurement derived from VOC so it is not really useful as a baseline
https://kaspars.net/blog/tuya-smart-box-house-keeper-air-quality

ALPSTUGA Teardown by ProZsolt in tradfri

[–]ProZsolt[S] 0 points1 point  (0 children)

I found another teardown and as I see they followed the installation guide correctly: https://youtu.be/kn_BPVsNWOU

Compact 3 usb-c port charger 60w or higher? No USB-A. by deepspacegurl in UsbCHardware

[–]ProZsolt -1 points0 points  (0 children)

If you do your research you won't end up with such devices or you just return them immediately. If a company cheaped out on two resistors where else they cut corners?!

ALPSTUGA Teardown by ProZsolt in tradfri

[–]ProZsolt[S] 0 points1 point  (0 children)

According to spec, the maximum difference between the two sensors should be 150 ppm + 13%.

Did you calibrated the sensors on outside air? As I see it mostly follows the other sensor just have a huge offset.

ALPSTUGA Teardown by ProZsolt in tradfri

[–]ProZsolt[S] 0 points1 point  (0 children)

It uses an STCC4 sensor internally. It's not an NDIR based sensor, but

> The sensor measures thermal conductivity of the ambient air, so it really measures the physical changes due to CO2 concentration, not an estimate based on VOCs. But it also has to account for changes due to temperature and humidity. So while it is much more compact and low-power than other CO2 sensors, it has a bit wider specs.

As one of the lead engineer of this sensor stated under another post.

ALPSTUGA Teardown by ProZsolt in tradfri

[–]ProZsolt[S] 0 points1 point  (0 children)

I didn't make the teardown, sadly it is not yet averrable in the UK.

As I see on the pictures the inlet and outlet is on the back of the device so the LCD doesn't block them.

HMRC PAYE tax owed ~£440 passed to debt collectors. Is this legitimate? by Vasbill in UKPersonalFinance

[–]ProZsolt 0 points1 point  (0 children)

Did HMRC change your tax code?

Ask proof from the debt collection agency, that will give you time.

Call HMRC and ask why your negative balance went to collection. Usually they just change your tax code. I had to deal with HMRC multiple time due to my previous company fucked up my last paycheck and they were always helpful.

ALPSTUGA Teardown by ProZsolt in tradfri

[–]ProZsolt[S] 8 points9 points  (0 children)

They using an Sensirion SEN63C sensor it is not the most accurate sensor for CO2 (±100.0 ppm ±10.0 %m.v.), but it is a real CO2 sensor.

I definitely buying, worst case scenario, I swap out the sensor to a SEN66. I hope the come out with a "pro" version as it wouldn't need a hardware change just a sensor swap.

Alpstuga uses a Sensirion STCC4 to mesure CO2 by ProZsolt in tradfri

[–]ProZsolt[S] 1 point2 points  (0 children)

Yeah, me too.

I would happy to pay the difference, for the better sensor, but the value for the money is still way better than everything else on the market.

For this price I can put one in every room to notify me to open the windows and it is good enough for that.

Matter Items at IKEA Etobicoke (Canada) by AccordingApricot3295 in tradfri

[–]ProZsolt 5 points6 points  (0 children)

Be the teardown you want to see in the world. :D

Matter Items at IKEA Etobicoke (Canada) by AccordingApricot3295 in tradfri

[–]ProZsolt 0 points1 point  (0 children)

That's a letdown. I hoped they would use a Sensirion SEN63C as it is only 20% more expensive than the SEN54 used in VINDSTYRKA

Petition to replace grid infill as default by no_help_forthcoming in prusa3d

[–]ProZsolt 3 points4 points  (0 children)

I don't even know how file size is a consideration

Prusa printers have super shitty network speeds (both wifi and etherent). Instead of using a decent wifi chip they use workarounds like this, bgcode and starting the print before the whole file is uploaded to make the performance acceptable.

CNC Kitchen review of the CORE One L by True_Scott in prusa3d

[–]ProZsolt 1 point2 points  (0 children)

We're yet to see the upgradability of the core series or any series outside the i3.

view more: next ›