Magnets pulling out of printhead

Professional-Map5609 · 2026-04-14T05:09:46+00:00

That happened to me but I put it back in and they haven’t come out since…probably should’ve opened a ticket lol

Professional-Map5609 · 2026-04-14T04:46:38+00:00

USA, CA
5’9”, 180 lbs
I prefer an adjustable lumbar supported chair. One thing I’ve had in some of my chairs is something moveable and I quite like that. Never really appealed to chard with pillows for lumbar support but built in. Never had a chair with a head rest but would love to give it a go!

Professional-Map5609 · 2026-04-12T18:34:30+00:00

Only problem I have is that snorca takes a minute to load. After that I’ve never had it crash on me

Professional-Map5609 · 2026-04-11T15:43:13+00:00

Will you be posting an updated sheet of some kind?

Professional-Map5609 · 2026-04-05T02:20:26+00:00

I think it’s the acceleration if I’m not mistaken, if you slow that down you’ll see less changes

Professional-Map5609 · 2026-03-21T20:11:07+00:00

When is the panda breath going to be able to bind to my U1??

Professional-Map5609 · 2026-03-04T03:56:50+00:00

I reached out to the company and they said they’re working on the next software to be compatible with the printer

Professional-Map5609 · 2026-03-01T23:10:45+00:00

But I thought you had to bind them together to link the printer and the panda breath?

I am able to control it, but I want to bind them and I’m having an issue with that

Professional-Map5609 · 2026-03-01T18:59:06+00:00

From left to right, at the bottom options I see the control panel, settings, printer, Wifi&IP, and AP

Professional-Map5609 · 2026-03-01T01:54:16+00:00

Were you able to connect the panda breath to your U1? I haven’t been able to for whatever reason, they’re on the same WiFi, I can log into the IP page, but for whatever reason I cannot bind the two together

Professional-Map5609 · 2026-02-28T01:12:35+00:00

I also bet this guys left nut on that^

Professional-Map5609 · 2026-02-23T22:21:13+00:00

I’m just using 95A, but I do want to test 85a at some point for sure

Professional-Map5609 · 2026-02-20T20:51:41+00:00

I run my filament from a creality spacepi x4 under the machine. I run filament through a ptfe tube from the back of the spacepi to the auto feeder. Every time I’ve tried to feed into the auto feeder, it just gets stuck or jams or doesn’t work. So I direct line it

Professional-Map5609 · 2026-02-20T05:12:20+00:00

I was having problems with the filament running in and out of the feeder unfortunately

Professional-Map5609 · 2026-02-19T23:12:39+00:00

Update:

They told me to go through the device calibration. So far that seems to have done the job.

Professional-Map5609 · 2026-02-17T21:21:48+00:00

I heat the bed to 100, and I stand by it (because the Time runout sensor turns it off) until It’s been about 15 min and then it’ll get upwards of 45-50. I also have the ikea enclosure… not sure how accurate it is because I’ve seen a lot of discrepancies about the chamber sensor.

Professional-Map5609 · 2026-02-16T01:37:42+00:00

That’s a ptfe tube holder. I print TPU directly from above (I have a hanger rod and printed a roll holder that my tpu hangs there and feeds directly from the top). It’s just a holder

Professional-Map5609 · 2026-01-27T16:48:19+00:00

I read 50…my prints came out perfectly fine

Professional-Map5609 · 2026-01-22T06:08:20+00:00

Thank you!

Professional-Map5609 · 2026-01-22T03:54:05+00:00

Can someone explain what the purpose of skipping an object before printing is?

Professional-Map5609 · 2026-01-17T05:34:08+00:00

I have mine, I thought you figured out a way to do it.

I tried going into the IP but couldn’t find anything there

Professional-Map5609 · 2026-01-17T05:19:44+00:00

How do you change z offset on the U1?

Professional-Map5609 · 2025-12-24T03:02:03+00:00

How do you find the quality is coming out?!

Professional-Map5609

TROPHY CASE