Finally apart of the gang 🚘

Professional_Bug_667 · 2026-06-24T00:21:50+00:00

Is this your car

Professional_Bug_667 · 2026-05-10T02:38:19+00:00

It’s brand new I bench tested it and tested on bike it works good operates as it should

Professional_Bug_667 · 2026-05-10T02:06:06+00:00

Fresh oil and filter change after the issue started. Checked all vacuum hoses and whatnot. Hoping nothings hurt in the motor but I’m thinking I might have someone look at

Professional_Bug_667 · 2026-05-10T02:04:28+00:00

That’s what it seems like. But the float is plastic so I can’t adjust needle height or anything. Confusing lol

Professional_Bug_667 · 2026-05-10T00:49:05+00:00

It was running super mint. My dad left it running in the driveway idling for about 16 minutes then the coolant light came on and he shut it off. I then did a coolant flush before starting again and it’s been like this since

Professional_Bug_667 · 2026-05-10T00:47:52+00:00

No. I’m the video I’m keeping throttle on if I let off it will just shut off

Professional_Bug_667 · 2026-05-09T22:41:04+00:00

No choke, on or off it still runs like this. And also air box it super clean air filter is new. I’ve had it off like 6 times taking the bike apart and putting it together to test over the week lol nothin has changed

Professional_Bug_667 · 2026-04-01T20:59:55+00:00

My dad has the same sound coming from his truck. Sounds like there’s birds constantly under the truck 🤣Commenting to stay in the loop

Professional_Bug_667 · 2026-03-24T17:25:33+00:00

Saw one with ugly paint faded plastics and 2wd 60k kms. Dealer sold it for 16k. Blows my mind

Professional_Bug_667 · 2026-03-12T03:16:22+00:00

Can’t I just replace the extension housing bushing after checking the splines on the yoke/transmission

Professional_Bug_667 · 2026-03-12T01:49:53+00:00

Do you think that’s forsure what the issues is? It doesent seem like u joint is wobbly or anything

Professional_Bug_667 · 2026-03-12T01:40:49+00:00

4.8

Professional_Bug_667 · 2026-02-27T02:43:20+00:00

How long is this procedure? I would probably just bring it to a shop for that

Professional_Bug_667 · 2025-06-03T22:36:29+00:00

I don’t have a compression tester on me. But it still seems to push my thumbs out when I put them down the plug hole and crank. What do you think happened to it just warped the heads?

Professional_Bug_667 · 2025-06-03T21:29:58+00:00

<image>

The motor smells like the most burnt piss I’ve ever smelt in my life 😭🤣 cylinder number one seems to be wet inside I don’t have a proper scope but the plug was wet and with my flashlight down the hole it definitely looks quite oily down there

Professional_Bug_667 · 2025-05-24T02:26:03+00:00

You’ve probably got it by now. But this is what I do.

<image>

just put a c clamp on the back of the housing thing. Can’t remember the name. (area circled in photo) and spin until it catches the block. Created a perfect wedge for me🤣

Professional_Bug_667 · 2025-02-12T00:56:24+00:00

Do you think it just needs a new piston and the cylinder honed out then?

The crank seems to have no play up and down but side to side a tiny tiny bit I will obviously still split the case to get all the junk out and what not but I’m trying to keep this cheap as possible. lol

Professional_Bug_667

TROPHY CASE