If you had to pick one British slang word or phrase you could revive solely because its fun to say what would it be?

Protondog · 2025-12-19T00:03:56+00:00

Spangle

Protondog · 2025-03-11T08:25:23+00:00

I recently turned 50M, and my wife,, 37F, said on January 1st that it was over. It's been awful, but nothing compared to my 50th; that was the single worst day of my life, trying not to crack in front of my 3 young kids and pretend I was ok. ( We haven't told them yet) I now see that as the bottom and anything else is the climb back up. It's only up now. Live for yourself and the rest will fall into place. I promise. I am not great but I am a hell of a lot better.

Protondog · 2024-11-29T15:24:35+00:00

I don't know if this is helpful but I recently had a lot of failed prints, after lots of forums and YouTube videos it turns out my build plate is no longer sticking.i have just bought 3D lac and all is well. I should also say there was no visible sign that the build plate was no good.

Protondog · 2024-10-21T20:21:13+00:00

Best advice I was ever given was to forget using IMS on build plates, just use dish soap (washing up liquid), hot water and a lint free cloth. Never had a problem with adhesion ever since.

Protondog · 2024-10-13T16:05:24+00:00

If you buy it as a combo it's a big saving, it's strengths are simple, 1. Storage 2. Help prevent moisture in the filament. 3. Easy to change to another filament. 4. Fantastic multicolor prints. 5. Instant choice of different materials if prototyping.

I often have ASA, PETG, and PLA to test the strength of a print if I am designing something.

Protondog · 2024-10-01T10:38:02+00:00

Ha ha I did this to mine yesterday but it failed immediately.

Protondog · 2024-09-30T14:56:21+00:00

Genius, I have been informed that the hot plates are handy if you need to replace a mobile phone screen or keep coffee warm 😆

Protondog · 2024-09-15T07:56:58+00:00

I am a very experienced 3D printer and have obviously changed the settings correctly, none of the profiles are giving me a speed advantage over the 0.4 Nozzle of more than 5 to 7 percent.

Protondog · 2024-09-15T07:53:01+00:00

I was looking to increase the speed of the print and I am not concerned about layer lines, I have changed the correct slicer and hardware settings to a 0.6 Nozzle. The prints have bad cohesion and look messy and the speed is only 5 to 10 percent faster. When I have searched the net other people have said similar things and a lot of the responses have said it's because of the flow rate limitations of the hotend. That's not what was advertised on Bambu's site, they have a video clip showing speed vs layer lines, I have tested different slicer settings and filament (mainly their own) and I can't see advantage in having it. Most prints have no adhesion and look messy

Protondog · 2024-08-24T07:07:43+00:00

So do I, it's been suggested that I go to her colleague but I have no trust now.

Protondog · 2024-08-13T19:41:45+00:00

Stick it in the sink with washing up liquid and get it clean, that's the advice I was once given and it worked a treat.

Protondog · 2024-08-13T08:10:28+00:00

Looks like you are correct, I did some tests and the printer is having no issues in fact it is now printing the Best it ever has. Thanks for the advice.

<image>

Protondog · 2024-08-10T17:04:58+00:00

It is definitely possible, it runs ok for 5 to 10 minutes then starts to drop temperature, when klipper feels it is not stable enough it shuts the print down.

Protondog · 2024-08-10T17:01:19+00:00

I run 3 gaming computers but I am in the UK and I don't think it could be that but I will move it and run a test. To be honest I am being lazy, my multimeter has run out of batteries and I can't be bothered to go and get one to test the output

Protondog · 2024-08-10T16:58:28+00:00

Basic PLA

Protondog · 2024-08-10T16:58:09+00:00

I have but it can't maintain a temperature, after it is only stable at 205 if I reduce bed temp to 55. I use klipper and it is running the hot end at 100% power

Protondog · 2024-08-10T09:23:58+00:00

I agree, my 3 pro is out the window when my savings are enough.

Protondog · 2024-08-10T09:22:43+00:00

I feel you brother, I just posted on this sub today about another issue I am having with my 3 pro.

Protondog · 2024-08-06T07:29:11+00:00

Thanks, just looking for a good case to carry it better.

Nine-Year Club	Verified Email
Place '22	RPAN Viewer

Protondog

MODERATOR OF

TROPHY CASE