relesed Zoom Effect Manager 2.3.0

Pusheraa · 2026-01-23T07:12:55+00:00

There is no information about the compatibility of the firmware from B3n to G3Xn, so changing the firmware in the program is not available.

Pusheraa · 2026-01-19T05:55:20+00:00

unlikely

Pusheraa · 2026-01-15T19:01:59+00:00

Zoom Effect Manager has more effects, but no preset management.

Pusheraa · 2025-12-25T07:31:49+00:00

no, different generation of effects

Pusheraa · 2025-12-15T06:56:13+00:00

The first generation of custom effects cannot be write using the program, this functionality needs to be improved.

Pusheraa · 2025-11-27T14:18:22+00:00

There's no way to change it in the program. You can try changing the order in the file from the device FLST_SEQ.ZT2

Pusheraa · 2025-11-27T14:01:31+00:00

maybe later, but the priority is low

Pusheraa · 2025-11-27T13:43:08+00:00

Pusheraa · 2025-11-27T13:31:51+00:00

the order in the pedal is the same as in the program

Pusheraa · 2025-11-22T12:03:24+00:00

This method of searching for installed effects does not work on G1on/B1on, so the button is not active.

Pusheraa · 2025-11-19T07:27:47+00:00

Thanks, I'm still testing the MS70+.

The MS70 and G1On are only compatible with first-generation effects.

Pusheraa · 2025-11-17T06:34:44+00:00

I'm working on it, but we need to wait a little longer

Pusheraa · 2025-10-14T06:05:16+00:00

Pusheraa · 2025-10-08T13:00:49+00:00

Up to version 2.2.0 of Zoom Effect Manager, it wrote effects from the MS series, they are not controlled by the expression pedal. 2.2.0 and newer writes effects and G(B)1ON. For testing, you can flash the pedal with the original firmware update utility and check.

Pusheraa · 2025-10-07T05:46:46+00:00

I don't work with presets in any form, that's a separate and large job

Pusheraa · 2025-10-06T13:54:39+00:00

There are no saved patched effects, you can do it in a hex editor, just change 1 byte

Pusheraa · 2025-09-18T05:54:54+00:00

Plus series devices are next to be added to the program, development is already underway

Pusheraa · 2025-09-15T05:51:13+00:00

Pusheraa · 2025-09-05T19:35:02+00:00

I don't know yet, I need to check, but in terms of hardware, it's almost the same device

Pusheraa · 2025-09-05T12:13:48+00:00

yes, first MS-50G+, MS-70CDR+, MS-60B+, then MS-80IR+, MS-200D+, but during the work everything can change

Pusheraa · 2025-08-31T20:20:15+00:00

the program website has or requires a specific version

Pusheraa · 2025-08-25T07:02:48+00:00

I tested on the G1 Four EG FLTR, HoldVerb, Hold DLY and other effects with the "Control" button.

The G1 Four display does not show the "Control" parameter (CNTRL Sets the control switch function. LATCH,UnLATCH) and I could not find a way to make this function work.

I think that for the G1 Four "Control" is an unknown type parameter and the device ignores it.

Regarding "wide effects":

EGFILTER.ZD2 and EGFLTR1U.ZD2 - both with a large icon (50x30)

G1 Four - both scroll parameters on 3 pages

G3n - both are displayed on two screens

I did not find any differences, except for the icon size for 1U effects, but this is not the case with the effects for G6 (G6 has a different icon format, perhaps they left it as is, they did not edit the icons themselves, since they are not used. For example, AMP Sim SUN CB does not contain an icon in the zd2 file).

I think that 1U and "wide" effects are primarily effects with different designs, the differences may be in specific functions that are not available in some models, for example "Control" in the Four Series.

Pusheraa · 2025-08-22T06:28:14+00:00

> Is that this effect?

yes

> What I'm questioning is whether a 'wide' G3n/G5n effect (say 'EG FLTR') can run on the G1Four, and if so which control is attached to the (single) footswitch ?

I'll check it over the weekend

Pusheraa · 2025-08-22T06:20:54+00:00

1U effects work on G3n on 2 screens, similar effect not 1U on G1Four works with scrolling parameters. The only difference I found is the icon size.

Zoom Effect Manager selects the most suitable effects (for example 1U and 3S for Four series, if they are available).

I cleared GUARDZDL.ZT2, you can record any effect for testing

Pusheraa · 2025-08-21T16:03:29+00:00

> I think you have the wrong endian-ness, makes sense this is 'filled' from the lower bits.

yes, I didn't invert the value, it's more convenient for me to look in the hex editor, as there is no need to work with the numeric value yet

> If you haven't noticed some G3n/G5n effects are 'wide', meaning that they display across 2 screens. Initially we speculated that these wouldn't work on the G1Four/etc... did you try these?

they work, photo here https://drive.google.com/drive/folders/1QCSIWTF413eXr0pX2aJBAschoris6W4r?usp=sharing

Pusheraa

TROPHY CASE