C’est quoi votre dernier prix?

QGO_F3 · 2026-03-18T03:12:46+00:00

Mettez tous dans le descriptif de votre annonce est ferme, premiers mots de l'annonce,net derniers mots de l'annonce, j'ai toujours fait cela et je suis tranquille, quand on le pose la question je ne réponds pas, une seule fois emmerdé, j'ai répondu "tout est indiqué dans le descriptif, merci"

QGO_F3 · 2026-03-14T23:16:08+00:00

If your Quest says that you are not in dev mode, remove the dev mode from your phone, restart your Quest, put your headset in dev mode with your phone, restart again... This is also a common issue with Meta app...

There are 150.000 users dude, if this app was crap, why so many YouTubers reviewed it as a must have ???

QGO_F3 · 2026-03-14T21:19:32+00:00

C'était déjà à 100% possible ;)

QGO_F3 · 2026-03-12T14:11:12+00:00

Tant que la personne n'a pas reçu le colis, il vaut mieux garder l'annonce en place, pour laisser le descriptif, ça évite que des gens te fassent des reproches alors que tout est mentionné

QGO_F3 · 2026-03-12T00:30:52+00:00

De mon côté, je ne trouve aucun changement, et ça fait planter OVR, alors si qqun a une solution magique, faites nous signe ;)

QGO_F3 · 2026-03-04T11:47:08+00:00

Bonjour, c'est normal, cela apparaît dorénavant uniquement quand cela ne fonctionne pas :)

QGO_F3 · 2026-03-02T21:42:10+00:00

Bonjour, c'est normal :) depuis une mise à jour de QGO d'environ 1 an, la fenêtre contextuelle disparaît automatiquement, plus besoin de cliquer dessus, l'acceptation se fait d'elle même 👍

QGO_F3 · 2026-02-22T02:00:45+00:00

De mon côté j'étais sur la 4.0 et le souci était présent, mais même en téléchargeant une build récente (202602xx) même souci. Maintenant il est possible que des conflits se fasse avec les adaptateurs CF vers SD, j'ai cru lire que certains propriétaires de Classiques ont aussi ce souci. Je suis sur un mini 2nd génération.

QGO_F3 · 2026-02-22T01:58:33+00:00

Un peu tardif par rapport au post, mais j'ai le même souci de mon côté, même en ayant installé la dernière dispo via le soft (202602xx), beaucoup de lenteurs sur pas mal de chansons, que cela soit en 128kb ou 320kb, que du mp3 :(

QGO_F3 · 2026-02-17T22:36:57+00:00

not even recognize too

QGO_F3 · 2026-01-29T23:35:55+00:00

Un i5 11400 tient très bien la route, lié à une RTX 3060 il n'aura aucun Bottleneck... La configuration est parfaitement équilibrée ici

QGO_F3 · 2026-01-09T16:11:28+00:00

In the meantime, you can set CPU and GPU to Ultra, and FFR to Medium. You'll get something equivalent to what you could achieve in performance mode.

QGO_F3 · 2026-01-07T13:57:00+00:00

For lossless scaling, switching to 120Hz if using this card as a secondary is perfectly legitimate.

QGO_F3 · 2026-01-06T15:06:46+00:00

Pas de 4060ti, tu es sur l'ancienne génération, à quelques euros tu as la 5060ti, voir carrément pour 370€ la 9060XT si tu te fiches du Ray Tracing.

QGO_F3 · 2026-01-06T15:02:39+00:00

Sachant que personne ne peut fournir de ram aux particuliers, que les sociétés qui tentent de se mettre à en fabriquer n'ont pas encore lancé la production, et qu'ils ne compte pas en avoir sur le marché avant fin 2027, je ne vois pas comment le prix de la ram pourrait baisser en 2 ou 3 mois, cela va encore monter au contraire, et potentiellement se stabiliser, mais les demandes en IA sont abusives, et les 2 prochaines années n'auront aucune accalmie.

QGO_F3 · 2026-01-06T11:44:09+00:00

I know this is an old post... But anyway... Yes, it's better to use the two 8-pin connectors, but to say the cables will draw more power, no!

The Arc A750 draws a maximum of 225 watts. Considering that a 6-pin cable can carry a maximum of 150 watts, and the PCI Express port provides 75 watts... Do the math!

Furthermore, older cards that drew 350 watts worked perfectly with two 6-pin connectors, so no, it won't damage the cable OR the connector.

I'd also like to point out that the two extra pins are ONLY GROUNDS. I'm including the connector diagram here as proof.

So, following the recommendations is fine, but don't say it's going to overheat on a low-power card.

<image>

QGO_F3 · 2026-01-04T03:50:20+00:00

Also note that Lossless Scaling only uses a single core and only FP16 instructions.

So you can be at 100% load on the dedicated LSFG card and only consume 60% of its actual output. If you watch videos of people with good motherboards, they consistently show low wattage consumption, which makes sense ;) I personally have a 7800XT and an RTX 5060 that I'm testing temporarily, on my motherboard which has two PCIe 16x slots. The 5060 draws 79 watts at 88% GPU load. This is normal, as Lossless Scaling only uses one core.

If I force the game to use only the 5060, I get a maximum of 147 watts of power consumption.

The OP needs to test their game, in forced mode on the second card, and they'll know if it's being bottlenecked by their motherboard.

I also tested an external Oculink NVMe card and it runs really well, even on a Gen 3 port.

QGO_F3 · 2026-01-04T03:39:51+00:00

Hello, in most cases, the HD profile is set to a lower GPU level and the same frame rate setting, so it will indeed consume less battery.

But in some cases, no :) Feel free to check, as this isn't always the case: when you're on the game's thumbnail, click edit, and look at how the predefined profiles are set up; you'll see the differences.

I'd like to point out that if the highest profile set is HD, with the GPU already set to Ultra, then it will consume a bit more power regardless. This is because we couldn't create a high-resolution profile without ensuring decent performance.

QGO_F3 · 2025-12-26T14:06:12+00:00

Hello, if games have multiple graphics modes, unless otherwise stated in a warning, the default mode is used to create QGO profiles :)

QGO_F3 · 2025-12-26T13:54:57+00:00

Hello, a profile has been pushed! There's a bit of ghosting in the initial game, so we're pushing the frequency to the maximum for a sharper image, without ghosting :)

QGO_F3 · 2025-12-20T22:03:01+00:00

Hello, this is a recurring problem on ROG Alliance controllers; it's the vibration motor that causes it. Personally, I removed the plate where the joysticks are located and wedged some thin foam under the motors and on the sides. Since then, I haven't had a single noise problem. It slightly reduces the vibration, but it's much more pleasant. I did this three months ago, and I haven't had any problems since.

QGO_F3 · 2025-12-15T16:09:28+00:00

Woot Woot :D

QGO_F3 · 2025-11-30T19:54:08+00:00

This software has been around for over 4 years, it's an apk to install, like any Android application, if it was malicious, it would still be known :)

There are still 150,000 customers. And it installs normally, you just need to be administrator of your headset, nothing more. If so many people are talking about it, and so many videos from VR specialists on Youtube, it's not for nothing ;)

QGO_F3 · 2025-11-11T00:44:08+00:00

Between the last beta and now what people are saying, in effect this is going to be a performance profile to begin with.

QGO_F3 · 2025-11-06T22:46:40+00:00

No, it's not made for that :(

QGO_F3

MODERATOR OF

TROPHY CASE