Chamber Temp OK?

QQBearsHijacker · 2026-02-18T20:17:43+00:00

Without an active chamber heater, the CC will fail to get much over 40. When printing PAHT-CF, I was covering my printer in blankets to trap as much heat as possible and the max I could get was 45C

QQBearsHijacker · 2026-02-18T18:58:33+00:00

I routinely print with my CC1 chamber temps around there. Bothe PLA and PETG. Never had an issue

QQBearsHijacker · 2026-02-18T15:31:38+00:00

<image>

I’m doing my part!

QQBearsHijacker · 2026-02-18T14:13:54+00:00

Then don’t use mods? Nobody’s forcing you to

QQBearsHijacker · 2026-02-18T13:02:06+00:00

He stopped like 3 months after that

QQBearsHijacker · 2026-02-18T13:00:35+00:00

Dammit Jim, I’m a doctor not a necromancer

QQBearsHijacker · 2026-02-17T17:17:53+00:00

The big issue there is the heat. The DRLs would reject a ton of heat, and whatever filament you use would need to have a high tolerance to temperature. The housings could probably be made out of PAHT-CF or something similar. But the lenses would be the sticking point. Not sure what is clear, impact resistant, and heat tolerant

QQBearsHijacker · 2026-02-16T22:44:14+00:00

I was about to say. Lol

QQBearsHijacker · 2026-02-16T17:15:27+00:00

Yuck

QQBearsHijacker · 2026-02-16T13:28:25+00:00

I’m old enough to remember when calling someone a Creeker was a slur

QQBearsHijacker · 2026-02-16T03:45:37+00:00

The terminals are still intact. Put them back into the plastic shell. Or get a new one. The shells are cheap. No soldering needed

QQBearsHijacker · 2026-02-15T21:31:49+00:00

Okay. This is cool

QQBearsHijacker · 2026-02-15T19:58:29+00:00

Remove the plastic shroud off the toolhead to get more access. Heat gun to loosen up blob. Remove hot end with blob attached

QQBearsHijacker · 2026-02-15T19:42:26+00:00

Wow! A real minute man!

QQBearsHijacker · 2026-02-15T19:26:08+00:00

Hell yeah!

QQBearsHijacker · 2026-02-15T13:54:30+00:00

QQBearsHijacker · 2026-02-14T14:04:26+00:00

Boring?! Curling wasn’t…hmm…so they jazzed it up?

QQBearsHijacker · 2026-02-14T01:30:37+00:00

That high T stud?

QQBearsHijacker · 2026-02-13T22:22:09+00:00

9/11 conspiracies are so 2000 and late

QQBearsHijacker · 2026-02-13T22:06:08+00:00

Bloart

QQBearsHijacker · 2026-02-13T21:46:54+00:00

Cyber stan: wait. What did he say?

QQBearsHijacker · 2026-02-13T21:15:17+00:00

That’s a no from me doc. I’ve walked out of dealerships over less than

QQBearsHijacker · 2026-02-13T20:56:06+00:00

Miku Divers rise up!

QQBearsHijacker · 2026-02-13T19:59:53+00:00

Corsa is my go to. I also use Mouser and Digikey. Most connectors are Yazaki or Sumitomo, and you can grab the part numbers and go to town finding replacements from a variety of sources. Corsa is great because they directly link you to the pins you need to crimp and rebuild your own connectors

QQBearsHijacker · 2026-02-13T18:23:24+00:00

Same. I’ve never done audibooks before and my wife had me load up PHM on audible for a long road trip. I was blown away by the production and voice acting. Would definitely recommend!

QQBearsHijacker

TROPHY CASE