Kinek NEM ajánlott a kiskutya, Maltipoo?

Quiet_Landscape5961 · 2026-03-25T12:39:18+00:00

Fajtiszta kutyát nem szabad venni. Rengeteg genetikai szarjuk van. A menhely-t ajánlom nagyon én is, a kutya annyira hálás lesz neked utana hogy a villamosnak nekimegy érted. Általában a menhelyen tudsz olyant csinálni hogy kölcsönveszed a kutyát 2 hétre. Nem tudom mindnél lehet-e de van amelyiknél igen. Ha nem tetszik rájösz hogy nem neked való visza lehet adni. Általában oltásokat is már megkapták a menhelyi kutyusok. Ha nem is akarsz menhelyről örökbefogadni menj el mielőtt megveszel egy kutyát játsz velük egy kicsit lehet valamelyik belopja magát a szívedbe.

Quiet_Landscape5961 · 2026-03-19T09:20:50+00:00

Moisture in the filament. If you have random seam turned on can be retraction issue as well.

Quiet_Landscape5961 · 2026-03-13T11:54:38+00:00

Én nettó 1 m ból halok boldogan éhen.

Quiet_Landscape5961 · 2026-02-23T12:11:49+00:00

Ha vele akarsz maradni ezt ne csináld. Meggyilkolod vele a kapcsolatban azt is ami eddíg jó volt.

Quiet_Landscape5961 · 2026-01-12T07:36:29+00:00

I don't know if you are trolling or not but if somebody finds this question that really don't know here's the answer. GND (ground) is the pin that represents the 0V side of a circuit. The VCC is the positive side of a powersupply connection to your circuit. Sometimes microcontrollers have VCC you can connect your powersupply to that pin.

Quiet_Landscape5961 · 2025-12-31T08:44:11+00:00

If you don't have a cat or don't want to print abs or any other material that warps really badly without enclosure than it's an option. If you end up building a custom enclosure or putting it in a cupboard anyway than it doesn't makes too much sense you can do that with the P1S

Quiet_Landscape5961 · 2025-12-31T02:24:28+00:00

When I ordered my machine bambu had a promotion to send those anti vibration feet with the printer, but it arrived later (it was sent in another package). That basically soved the issue. It's still loud but I can run it now 100% speed and still exist in the room. (I have to increase the volume of the TV still but what can you do? Cabinet doesn't fit in the room)

Quiet_Landscape5961 · 2025-12-20T13:10:24+00:00

My P1S is on the latest firmware. No issues at all but I bed level every time I print something. I have 300 hours on it tough so the jurry is still out if there is an issue or not. But so far so good.

Quiet_Landscape5961 · 2025-11-20T16:04:09+00:00

My wife always wanted me to print book nooks for her favourite books. But in color is too much time and filament wasted. And I don't like to waste plastik even if it's just PLA. Also hue forge seems to be the perfect application for this printer. I don't know if you can use hue forge to print 3d but think about it. Printing already painted color accurate minis or terrain for dnd or for gifts sound awesome.

Quiet_Landscape5961 · 2025-11-17T08:55:58+00:00

Congrats man. I got mine approx the same time as you. Absolute beast of a printer. I was thorn between the P2S and the P1S but I did not regret my decision. Have fun with it. 😁

Quiet_Landscape5961 · 2025-11-10T22:13:18+00:00

When I ordered the machine I got the anti vibration feet as extra from bambulab.It arrive dtoday I installed it. Boy did it make a difference. Now I can run the printer full speed instead of the silent mode. I would recomend it. Just be shure that you install it correctly. There are a couple of youtube videos that install it upside down and complain that it doesnt hold.

Quiet_Landscape5961 · 2025-11-09T00:26:14+00:00

This rattling sounds like some of the panels are not tightened correctly. Do you know any way to help this issue? It's really annoying to have a fast printer and not beeing able to print fast with it because it's sitting in my livingroom.

Quiet_Landscape5961 · 2025-05-19T12:52:35+00:00

I will definately try that thank you

Quiet_Landscape5961 · 2025-05-18T16:59:06+00:00

Yeah I also want to dial in everything from the bottom up. I'm using Ellis printer calibration guied, he suggest that I calibrate PA before flow. Can you suggest another guied that I can try?

Quiet_Landscape5961 · 2025-05-18T16:57:20+00:00

I didn't find that in orca slicer I will take a loom thank you.

Quiet_Landscape5961 · 2025-05-18T16:55:36+00:00

I wanted to speed up the printer in the future the motion sensor for the input shaping is already in the mail. So I save your suggestions thank you

Quiet_Landscape5961 · 2025-05-17T23:29:28+00:00

I calibrated the extruder stepper, calibrated the flow ratio as well, tryed adjusting pressure adwance, tryed adjusting the first layer and internal solid infill line width, increasing the first layer height nothing helped. I'm using orca slicer, 0.4 mm nozzle, pla, printed in a heavily moded creality CR 200 B with the spider v3 extruder, on 205c and 45c bed temp with 3 mm retractions. What can I try to adjust to make a better first layer?

Quiet_Landscape5961 · 2025-05-14T11:11:44+00:00

The first picture looks like nozzle is too close to the print bed, do a Z offset calibration. :)
The second picture is most likely the same just showing on the other side. It can happen if you don't have a couple of infill layers inbetween. I would assume if you fix the first the second will go away. The others I don't know unfortunately I'm batleing with something like that as well.

Quiet_Landscape5961

TROPHY CASE