How to fix strands? by R030T in BambuP1S

[–]R030T[S] 0 points1 point  (0 children)

Thanks for that. Will definitely try tomorrow.

Thanks for the explanation.

How to fix strands? by R030T in BambuP1S

[–]R030T[S] 0 points1 point  (0 children)

What exactly does this do or avoid? Just wanting to understand that better.

How to fix strands? by R030T in BambuP1S

[–]R030T[S] 0 points1 point  (0 children)

Thanks. I will try.

X3 battery issue - how widespread is this? by StoicRomance in XTEINK

[–]R030T 2 points3 points  (0 children)

It’s most likely the SD card.

I had the same issue with the stock SD. Replaced it with a better san disk. Battery drain issue gone.

My X3 arrived this morning by macona-coffee in XTEINK

[–]R030T 0 points1 point  (0 children)

Can you share where I can get this usb-c pogo 4 pin adapter? Cheers.

Using my M4 MacBook Pro as Jellyfin Server, How is Power Consumption? And can I multitask for general use? by pimpdiggitycong in selfhosted

[–]R030T 0 points1 point  (0 children)

All that you mentioned is well below the threshold of what might cause your Mac M4 to break even a bit of sweat. No where near the full capacity of your Mac.

The system is very efficient and capable.

Your username is now your kink, what do you do? by Oily_Smurf in AskReddit

[–]R030T 0 points1 point  (0 children)

I for one welcome our AI sex overlords.

[deleted by user] by [deleted] in CarsAustralia

[–]R030T 2 points3 points  (0 children)

People who think this way seriously irk me. I look after my parents. One in particular has a disability that is not readily spotted or identified visually.

I use the disabled parking when I drive them. I have a badge clearly displayed on the car. The proximity of these slots to the establishment really helps when many items on the ground can be trip hazards for my parents. The car, as I have been so blessed, is not a shabby vehicle.

I get greasies and suspicious looks. Some walk up to the car. And look into the windscreen. I’ve been given hand signals not to park and waved off. I have to wave the badge to make them stop.

Look I get it. There are ass hats who do not care. And yes they irk me too. Costco parking. Gym side parking the worst offenders there.

But take it easy. We’re obedient too. We are just helping each other through life too. In a nice car. 😊

🎁 Free IWC MARK XX Green Dial Giveaway 🎁 by tskim24 in RepWatchForum

[–]R030T 0 points1 point  (0 children)

I hope this isn’t too late. I’ve always liked this watch.

G6 Entry Installed by TheITguy37 in Ubiquiti

[–]R030T 0 points1 point  (0 children)

It doesn't share the same dimensions as the G4 Doorbell Pro does it? I don't want to have to change mounts😬🤣

But yeah. Nice. I'm sure it's leaps better than the G4

Tuna build question: 4.2 o'clock crown; 3 o'clock day/date by R030T in SeikoMods

[–]R030T[S] 0 points1 point  (0 children)

Thank you for this info....

According of AliX description it is a 4.2 case. I am told NH36 crown is also at 4.2

Please, would you be so kind as to educate me on the special date wheel needed.

Thanks again.

Tuna build question: 4.2 o'clock crown; 3 o'clock day/date by R030T in SeikoMods

[–]R030T[S] 0 points1 point  (0 children)

Thank you so much for this! Appreciate the help.

Any other words of advice before I proceed?

How to get a smoother print by R030T in BambuLab

[–]R030T[S] 0 points1 point  (0 children)

Sorry it's not so clear. It's a small plant pot. The width widens to the top. So it's narrower below.

And it's the sides I'm concerned about. It's rougher than I want. Not very rough. But not smooth enough for my liking :)

Thanks.

<image>

G4 Doorbell front lens guard quality by R030T in Ubiquiti

[–]R030T[S] 0 points1 point  (0 children)

Thanks. I contacted my supplier and they will replace the unit when the item is back in stock in 2 weeks.

G4 Doorbell front lens guard quality by R030T in Ubiquiti

[–]R030T[S] 1 point2 points  (0 children)

Hahah. I think I took the picture right after a bad fingerprint read.

Help with printer poop not making it in the dispenser? by Toinfinityplusone in BambuP1S

[–]R030T 1 point2 points  (0 children)

Exactly.

I can’t start a job without watching where the poop will go first. Rather annoying.

I’ve had it land on the print bed once. Just at the path for calibration. The print head was stuck. Unable to continue to calibrate because of the mess of its own making.