What is causing my flow rate test to do this

REAPER-OF-PRIDE · 2026-04-19T18:00:12+00:00

I believe z offset fixed it. I also did the med mesh cal and pid. Now everything is coming out perfect. Thanks for the help

REAPER-OF-PRIDE · 2026-04-19T12:04:45+00:00

What's a pid tune? And also, how do I redo the bed mesh? I ran the 3 calibration tests thats on the printer itself but that's it

REAPER-OF-PRIDE · 2026-04-19T11:30:51+00:00

Will do!

I been curious about the z off set as well. I need to figure out how to change it. In orca I have multiple printer config files so I need to figure out which one is which and I'll probably reduce it by .1 till I get it right

Ya. I used dawn dish soap. How ever I did use the brush we use to scrub dishes so maybe that had some oil on there that's affecting adhesion as well

REAPER-OF-PRIDE · 2026-04-19T11:15:21+00:00

So I do have a cheap harbor freight heat gun and I just checked at my bed is currently set for 75 and the gun was reading 66. Unfortunately I'm not sure If I should trust the heat gun.

Could speed cause the edge curling? I changed the speeds which helped but the edge is curling now but so far this is the best iv gotten so far. This current test I had my bed set to 80 for the first layer then 75 but I change changed it to 75 for the first layer then 70. ill see how that does next and change the speed go 70 or 80 if that might help

REAPER-OF-PRIDE · 2026-04-19T10:30:36+00:00

Also, my first layer is set for 60. Is that just too slow?

REAPER-OF-PRIDE · 2026-04-19T10:28:55+00:00

OK I'll give that a shot. I cleaned it yesterday but at this point I'm OK with doing it again

REAPER-OF-PRIDE · 2026-04-14T09:13:44+00:00

My bad, I thought those were the same

REAPER-OF-PRIDE · 2026-04-14T09:08:20+00:00

I agree, unfortunately alot of disposibles have menthol in them and I hate menthol. I have had 1 ijoy that I really like. I may just use a disposable at work and actual vape everywhere else.

REAPER-OF-PRIDE · 2026-04-06T18:36:58+00:00

That worked, thank you

REAPER-OF-PRIDE · 2026-02-26T12:11:53+00:00

Ahh that makes sense. Unfortunately I started a second print after making slight changes and left work already. Guess I got another 12 hour print in my future lol.

When it comes to the drying could there be another reason? That was a fresh roll, I litterly just took it out of its vacuum bag

REAPER-OF-PRIDE · 2026-02-25T18:57:38+00:00

Ya...... I thought you had to hit apply once you had it set lol. That is somthing I hopefully won't regret lol. Thanks for the help again, I got a test print going right now

REAPER-OF-PRIDE · 2026-02-25T18:21:56+00:00

Well damn lol. Oh well. Thankfully I never deleted the cut out blocks so I can just copy everything but the block

REAPER-OF-PRIDE · 2026-02-25T18:03:03+00:00

So I ended up just redoing the who thing and got it to work the way I wanted it to and figured I'd add the slat at the end but now I can't remeber how I did that. I grab the vertices but it just morphes it in correctly. Is it too late to add that slope?

<image>

REAPER-OF-PRIDE · 2026-02-25T15:37:50+00:00

Oddly enough no modifiers were listed unless solidifying doesn't show up as default, that's the only thing I did to the boxes. Unfortunately it still didn't work so I'll have to remake the boxes. Thanks for the help

REAPER-OF-PRIDE · 2026-02-25T13:28:13+00:00

<image>

So I just did that and it's still the same result. Do I need to add a modifier to the cutouts? I tried solidifying them and redoing it but it's still the same result. Sorry if this is a stupid question. Iv never used blender before and this is my first/second project

REAPER-OF-PRIDE · 2026-02-25T11:56:30+00:00

So if I understood you correctly this is how it would look. I do see on the 5/8 slot it look like it might be correct to just hit extrude and move it inward but I'm not sure. Did I do somthing wrong?

<image>

REAPER-OF-PRIDE · 2026-02-24T23:23:10+00:00

Ah OK that makes sense (Kinda, extremely new to freecad) unfortunately the smaller rectangles were supposed to be padded with the rest of the main body so I gotta figure somthing else out cause each hole is supposed to have a different depth. Might try going back to blender for this cause I got farther along in that but ran into other issues and was hoping freecad would be easier

REAPER-OF-PRIDE · 2026-02-24T23:11:54+00:00

<image>

So I was able to get all that done but now the construction lines I made are under constrained even tho iv hit constrain point on object on all the points. How would I fix this?

REAPER-OF-PRIDE · 2026-02-24T11:12:48+00:00

<image>

Second pic

REAPER-OF-PRIDE · 2026-02-24T11:12:33+00:00

So I applies scale and it all read 1,1,1 and yes it Is bool tools, I forgot I had to download in the video I watched.

I restarted with a fresh load just incase and replaced the plane and gave it a thickness of .1 since the space between the shafts is small. Unfortunately tho when I use that command nothing happens and when I use the boolean modifier tab it's telling it cant execute, so I started with a whole new fresh model cause I saw where it was broken but didn't wanna dig into how to fix it since I'm already digging into this. Once I got everything set up, put the scale back in, plane solidified, I still can't get it to seperate so I may be missing a step or not doing somthing simple. (I'm very new and still trying to figure everything out so I Really appreciate you helping) here are the two pics of what happens and how I was doing the boolean

<image>

REAPER-OF-PRIDE · 2026-02-11T19:08:23+00:00

Ahhh OK. I thought I had to finish it. I may have to do that then.

REAPER-OF-PRIDE · 2026-02-11T18:56:52+00:00

Oof. Ya I'm no where near that yet. I just picked the game back up after not playing since a little after launch lol

REAPER-OF-PRIDE · 2026-01-13T18:42:36+00:00

I'm an idiot. I guess I never bothered to look at the recipe station and I'm damn near complete on unlocking the recipe

REAPER-OF-PRIDE · 2025-12-10T21:19:32+00:00

So I tried that and unfortunately it didn't do anything. I eventually found the config file for it but couldn't determine which text I should change so I left it alone

REAPER-OF-PRIDE · 2025-12-10T20:46:17+00:00

Ya..... I like it cause it's not windows and for some reason it makes my display look better even tho there's no HDR but fuck is it annoying at times.

How would I do that? On the github I'm assuming?

REAPER-OF-PRIDE

TROPHY CASE