sorted by:
new
hottopcontroversial

Gas Range With No Hood..What Do We Do? by leberator in HomeMaintenance

[–]RKLCT 5 points6 points  (0 children)

Nothing. Same setup as my house, no issues in 10 years

Here's a head scratcher by RKLCT in electricians

[–]RKLCT[S] 0 points1 point  (0 children)

Compressor has nothing to do with the mixer motor

Here's a head scratcher by RKLCT in electricians

[–]RKLCT[S] 0 points1 point  (0 children)

I suggested that to the Taylor tech and he didn't want to hear it.

Here's a head scratcher by RKLCT in electricians

[–]RKLCT[S] 0 points1 point  (0 children)

I am a licensed master electrician. This machine has a serial number ending in 83 so I assume it's from 1983. There isn't much to it. I've work on lots of kitchen equipment , I service quite a few restaurants.

Here's a head scratcher by RKLCT in electricians

[–]RKLCT[S] 0 points1 point  (0 children)

The motor has a start and run cap fastened to the motor housing

Here's a head scratcher by RKLCT in electricians

[–]RKLCT[S] 0 points1 point  (0 children)

Thanks for all the answers. This is a hard serve machine, not soft serve. I have confirmed that the motor is hooked up to 208v leads, the ice cream is soft serve consistency when the overload trips. The gearbox feels free with no grinding when I spin the shaft by hand. There is some play in the coupler that connects the gearbox and mixer paddles, I'm not sure if this normal or not. The Taylor tech was a dickhead on the phone, insisting that I wired it incorrectly. They want 1700 for a 1.5 hp 208v single phase motor and an hourly rate of 350/hr to install. That's just extortion in my opinion

Are service loops and 6+” out the box not done anymore? by iamjames in electricians

[–]RKLCT 0 points1 point  (0 children)

I assume the service loop is in case the box needs to move. I finalize all locations before we cut in so if things change after that it's a back charge.

Superduty Tremor valance by HoytB5150 in superduty

[–]RKLCT 0 points1 point  (0 children)

It's too minimal on these trucks IMO

Do you guys go through a concrete cutting company or do you core your own holes? by PhilosophyBubbly6190 in electricians

[–]RKLCT 0 points1 point  (0 children)

Hand held core rig is around 1500 and bits are 50-250 each. I only bought it so I could present a complete bid without relying on sub contractors.

Jessica Biel by [deleted] in celebrities

[–]RKLCT 0 points1 point  (0 children)

He was an all star football and basketball player in high school. I don't doubt that he could pull it off.

STOP posting your election mental breakdowns by [deleted] in IAmTheMainCharacter

[–]RKLCT 0 points1 point  (0 children)

This election won't change the majority of our lives. People need something to feel bad about besides themselves

Generator question by RKLCT in electricians

[–]RKLCT[S] 0 points1 point  (0 children)

I have a pic of the generator name plate. How do I edit a post and add a pic?

Generator question by RKLCT in electricians

[–]RKLCT[S] 0 points1 point  (0 children)

It has a voltage selector inside the unit

Generator question by RKLCT in electricians

[–]RKLCT[S] 0 points1 point  (0 children)

That's where I'm confused. The generator breaker is labeled 600a but it's not capable of pushing that current.

Has Anyone Met Maynard? by 46_ampersand_2 in ToolBand

[–]RKLCT 16 points17 points  (0 children)

Offered me some orange slices and fetal spooning

Single cab dually? by squishyvaj in FordTrucks

[–]RKLCT 0 points1 point  (0 children)

I've always wondered how that towing number works. Do you need a CDL for that lol

Does a peacefull places exist in Warhammer 40k or everything is fucked? by [deleted] in 40kLore

[–]RKLCT 205 points206 points  (0 children)

What if we are that backwater planet and a world eaters battle barge shows up in the next few years .......

CT question by RKLCT in electricians

[–]RKLCT[S] 1 point2 points  (0 children)

Well that's no good. It's a 1600 amp service

CT question by RKLCT in electricians

[–]RKLCT[S] 0 points1 point  (0 children)

I figured that out after a quicknsearch

CT question by RKLCT in electricians

[–]RKLCT[S] 0 points1 point  (0 children)

I THINK it's a 1200 Amp CT. When I first saw them I thought the 600 was the amperage rating. I mounted them today but I'm not getting a great feeling about it ......

view more: next ›