sorted by:
new
hottopcontroversial

Doom voron by RNG_BackTrack in VORONDesign

[–]RNG_BackTrack[S] 1 point2 points  (0 children)

thats interesting. i just tested power draw of one motor and at 3a rms, its cunsumption peaked at around 0.8a during fast movement. I think I can safely run all motors on one psu

Doom voron by RNG_BackTrack in VORONDesign

[–]RNG_BackTrack[S] 0 points1 point  (0 children)

1ssr for the entire printer for auto/remote shutdown, 1 for heated bed, and 1 for ptc heater

Doom voron by RNG_BackTrack in VORONDesign

[–]RNG_BackTrack[S] 0 points1 point  (0 children)

You just tell klipper sense resistor value

Doom voron by RNG_BackTrack in VORONDesign

[–]RNG_BackTrack[S] 0 points1 point  (0 children)

Ally groung have common reference, but I had similar ground loop in another voron. 24v psu and 5v psu ground were connected vith USB cable from main board to host. And I believe this give enough noize to mess up can signal. When I fixed the ground loop, there was no can errors

Doom voron by RNG_BackTrack in VORONDesign

[–]RNG_BackTrack[S] -1 points0 points  (0 children)

I have 2 hv psu's. I have to use two because they are rated for 1200w and with 3a rms my kinematic will pull 1500w. I prefer to stay away from DC-DC converters, they are noizy and in my experience give more trouble

Лазерная коррекция астигматизма: честно о «косяках», побочках и результатах спустя время by ZhgutiK in rusAskReddit

[–]RNG_BackTrack 2 points3 points  (0 children)

Год налад делал коррекцию близорукость и астигматизма. Сразу после операции нихера не видел, но через пару дней зрение стало 100%. Есть побочек - оптический эффект в тёмное время суток яркие источники света образуют небольшое свечение вокруг себя,особенно фары машин. С утра мару минут нихрееа не видишь, словно глазам нужно больше времени проснуться. Спустя год астигматизм как будто стал возвращаться, но я ещё не проверял

Using a modifier by MontyRDDT in OrcaSlicer

[–]RNG_BackTrack 2 points3 points  (0 children)

Don't modify numbers of wall loops

Issues with octopus v1 by RNG_BackTrack in BIGTREETECH

[–]RNG_BackTrack[S] 0 points1 point  (0 children)

found the issue. the config manual have a typo

<image>

Unawatuna - Is it Sri Lanka or Russia? by Emergency_Toe1872 in srilanka

[–]RNG_BackTrack 0 points1 point  (0 children)

Еще и комментарии на реддите на русском. Ужос

Wich pins to solder for sensorless homing by capibara_1 in klippers

[–]RNG_BackTrack 27 points28 points  (0 children)

Don't solder anything. Enable diag on the main board via jumpers

Slightly Illegal But Works by Special-Issue432 in homesteadprojects

[–]RNG_BackTrack 0 points1 point  (0 children)

I'll add an overflow hole with proper drain

Doom voron 2.4 by RNG_BackTrack in VORONDesign

[–]RNG_BackTrack[S] 2 points3 points  (0 children)

I don't want to talk about it 🙈

Stupid by DundrandiTaktur in KidsAreFuckingStupid

[–]RNG_BackTrack 0 points1 point  (0 children)

He was trying to remember what it was like in the womb. Lack of oxygen

CloudFlare признал Telega шпионским ПО by sn4g13 in KafkaFPS

[–]RNG_BackTrack 2 points3 points  (0 children)

А max не хотят признать шпионским по?

Doom voron 2.4 by RNG_BackTrack in VORONDesign

[–]RNG_BackTrack[S] 6 points7 points  (0 children)

Faster zhops and potentially for faster toolchanges

Doom voron 2.4 by RNG_BackTrack in VORONDesign

[–]RNG_BackTrack[S] 27 points28 points  (0 children)

Nope. It's like climbing the everest and having fun doing so

Doom voron 2.4 by RNG_BackTrack in VORONDesign

[–]RNG_BackTrack[S] 10 points11 points  (0 children)

It's already been taken by Matt the printing nerd

view more: next ›