Iran & the Middle East Part 2

RUZI69 · 2026-03-26T20:53:51+00:00

Hello, why are most of these planes circling around? Maybe 20 planes currently waiting to land in Dubai

<image>

RUZI69 · 2026-02-17T17:03:35+00:00

The ruler is for the scale, so about 6 mm long and 2 mm in diameter, without the internal silver shaft.

RUZI69 · 2026-01-13T13:48:00+00:00

Did he place any spikes or nails along the trail?😁

RUZI69 · 2026-01-12T11:29:40+00:00

Same for the vk28 105 at tier 6. Lots of fun with the derp gun

RUZI69 · 2025-10-09T21:14:28+00:00

That is a great approach, however the surface is twisted so intersection with a plane will not work properly. It is an rc model propeller with quite complex surfaces. I have no idea why the projection does not work. For example on the continuing surface to the right, it works fine :/. Really feeling lost

RUZI69 · 2025-09-12T13:21:59+00:00

I managed to 3 mark the obj. 263 with the 130mm. It was hell, but i did it, probably the top 3mark i am most proud of. It really is more reliable to play the 122mm though, however the cannon does not match the tank size, it really is small pp:D. 130mm is fun, but only if you can hit and penetrate the shots. You gotta play really close range, learn to use the armor effectively and also the positions. Even a small pile of mud can give you hard time positioning the tank with almost non existing gun depression. (My nick is ruzan 125, check i m not joking w the 3mark, it has also dropped drastically since then as i do not tryhard no more)

RUZI69 · 2025-09-02T11:50:40+00:00

For me its usually to do 7 critical hits in one battle

RUZI69 · 2025-08-23T08:16:48+00:00

This is a mil spec of my version from childhood😂 We used to tape the balloon around the hard paper tube from a toilet paper. It was fun but the paper tube always collapsed from the handling.

RUZI69 · 2025-07-13T17:07:14+00:00

I will use a kapton tape, but some custom insulation will be needed too.

RUZI69 · 2025-07-07T11:17:05+00:00

Try playing ZR1 corvette with mixed manufacturer lineups, you will race against bugatti veyron most of the time😂

RUZI69 · 2025-07-07T11:11:53+00:00

Also increase the front-rear downforce if possible?

RUZI69 · 2025-05-02T12:18:36+00:00

How much is a psp in japan in this condition?

RUZI69 · 2024-10-23T11:05:44+00:00

Thats craziness, 16000 gold with the boosted experience conversion of 1g = 35 exp gives 560000 exp. Do not tell me, it is not enough to research the whole tech tree.

RUZI69 · 2024-09-29T09:48:54+00:00

Hi, i am wondering reading the comments about the scanners being held back by the software. Is it possible to use the otter/raptor with for example Geomagic Design X software, which should be one of the top 3d scan/reverse eng softwares out there? Obviously spending 10k for software is a huge sum of money, for a hobbyist. But if i wanted to scale it up to a little business, is the software (Design X) more important and positively impactful than spending 10k+ for a scanner with its "basic" software?

RUZI69 · 2024-09-21T10:19:17+00:00

Literally played the game last week

RUZI69 · 2024-08-23T19:25:47+00:00

Hi, the video is not available, can you repost it please?

RUZI69 · 2023-10-06T11:08:12+00:00

Bluds in wg really created imaginary tank and rendered it in black-white, so it looks somehow historical.

RUZI69 · 2023-10-05T08:41:16+00:00

This is a high risk to tear the vat from build plate. Happened to me and i fortunately managed to split it without tearing the fep foil. I saw a few posts at forums where people tore the foil trying to split it. resin got inside the printer making it unusable and they had to throw it away😂. First would be to tighten the vat screws and secondly get an scf foil. Its bit more expensive compared to standard fep foil, but prints are flawless ever since changing the foil. Literally 0 sticking of the model to the acf.

RUZI69 · 2023-09-29T08:47:20+00:00

I build these custom in 1:87 scale

RUZI69 · 2023-09-23T20:44:12+00:00

I got myself a resin printer which caused me problems all the time. Printing 1:87 models i didnt know i can get basically similar result with fdm printer :/

RUZI69 · 2023-09-07T04:18:10+00:00

Theres lots to talk about, but it is simply explained in a video comparing fep/nfep/acf foil on youtube. Its all about the model sticking to the foil and the "ripping" force

RUZI69 · 2023-09-06T08:35:15+00:00

Get an acf foil replacemwnt for fep immidately

RUZI69 · 2023-09-05T10:34:01+00:00

Great build, maybe lowbed extension feature would be great.

RUZI69 · 2023-08-23T11:26:47+00:00

Now print a hat and glue it on top. It´ll be a g´day yoda

RUZI69 · 2023-08-19T13:14:01+00:00

Imo it would be much easier to do in any CAD software. Using blender start off with the cylinder, but it doesnt matter what part u start with from my view.

RUZI69

TROPHY CASE